特高压快速接地开关的研制

特高压输电线路上,潜供电弧对线路产生的影响不容忽视,潜供电弧的顺利熄灭是实现单相自动重合闸的必要条件.稳态下潜供电流和恢复电压幅值是潜供电弧熄灭的两个决定性因素.快速接地开关作为重要的电器设备,越来越多的应用于电力系统中.快速接地开关除了在系统发生故障时接地外,还能快速关合潜供电流和降低恢复电压.本文根据750kV系统潜供电弧的特点和熄弧要求,研制了一种快速接地开关,着重对触头系统进行了研究,计算了触头压力、触头电动力及断口开距的大小,给出了快速接地开关整体设计思路和结构图.     

NUMERICAL ANALYSIS AND EXPERI- MENT OF UNSTEADY THERMAL FIELD OF ROTOR PLATE FOR EDDY CURRENT RETARDER

The physical model based on heat transfer theory and virtual boundary method for analyzing unsteady thermal field of rotor plate for eddy current retarder used in automobile is established and boundary conditions are also defined. The finite element governing equation is derived by Galerkin method. The time differential item is discrete based on Galerkin format that is stable at any condition. And a new style of varying time step method is used in iteration process. The thermal field on the rotor plate at the radial and axle directions is analyzed and varying temperature at appointed points on two side-surfaces is measured. The testing and analytical data are uniform approximately. Finite element method can be used for estimating thermal field of the rotor plate at initial design stage of eddy current retarder.     

三维有限元法分析频率对接地电阻的影响

提出了用涡流场的A-V有限元分析方法计算接地系统接地电阻的方法,分析了入地电流频率的变化对接地电阻的影响。计算结果表明,频率对接地体自身电阻的影响较大,但对散流电阻的影响很小。     

三相异步电动机运行指标的分析

利用电机学理论分析了影响电机起动转矩、起动电流、最大转矩和最小转矩的因素。     

SECANT-FUZZY LINEAR REGRESSION METHOD FOR HARMONIC COMPONENTS ESTIMATION IN A POWER SYSTEM

In order to avoid unnecessary damage of electrical equipments and installations,high quality power should be delivered to the end user and strict control on frequency should be made, Therefore, it is important to estimate the power system's harmonic components with higher accuracy. This paper presents a new approach for estimating harmonic component in a power system using secant - fuzzy linear regression method. In this approach the non - sinusoidal voltage or current waveform is written as I linear function. The coefficient of this function is assumed to be fuzzy number with a membership function that has center and spread value. The time dependent quantity is written as Taylor series with two different time dependent quantities. The objective is to use the sample obtained from the transmission line to find the power system harmonic components and frequencies. We used an experimental voltage signal from a sub power station as a numerical test.     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。     

高速电路中地电流的影响及其对策

从理论上分析了产生地电流干扰的原因，从而在实践上提出了一些经常被忽略，却是行之有效的方法来减小地电流的干扰，设计出高质量的电路。     

主电机轴瓦异常情况分析解决办法

介绍南钢中板厂四辊轧机主电机轴瓦一种非典型故障现象，原因分析及解决办法，提出了对类似问题个人见解。     

First Harmonic (2f) Characterisation of Resonant Frequency and Q-Factor of Micromechanical Transducers

In this paper, the response to the first harmonic component (2f) of the electrostatic force in single terminal driven electrostatic comb-drive and parallel-plate drive was used as a signal to extract device parameters, namely, the Q-factor and resonant frequency instead of the fundamental (1f) resonance response. It is shown that the difficulty in motional measurement due to electrical cross-talk (parasitics) using 1f measurement can be overcome with a higher signal-to-noise ratio of the 2f signal. Both atmospheric (low-Q) and reduced pressure environment were investigated using off-chip electronics and lock-in amplifier. The measurements were done on the electrostatic comb-drive and capacitive parallel plate sensing plates that form the two core modules of a yaw rate sensor (dual-axis resonator). The effects of AC and DC bias voltages on the measured response have been investigated. Experimental amplitude and phase response data have been analysed using the Lorentzian curve-fit, Resonance Curve Area (RCA) method, the half-power bandwidth method (3 dB) and the Nyquist plot for data fitting and determination of the Q-factor and resonance frequency.     

万用表电压测量法查找直流接地故障

直流电源是发电站的主要设备，一旦直流系统发生接地故障，将会严重地危及到发电站的安全和经济运行。因此，本文介绍一种简单易行，能快速找出直流接地点的方法一万用表电压测量法。