Jitter Tests and Studies for the Azimuth Axis of the TMT Tertiary Mirror System

太阳辐照度绝对辐射计的灵敏度研究与优化

衣小龙^1,2,方伟¹,骆杨¹,夏志伟¹,王玉鹏¹

（1. 中国科学院 长春光学精密机械与物理研究所,长春 130033;

2. 中国科学院大学,北京100049）

创新点说明：

1）通过理论分析以及实验测量的手段,研究灵敏度非线性误差对太阳辐照度绝对辐射计测量精度的影响;

2）提出了太阳辐照度绝对辐射计的测量新方法,通过实时修正灵敏度补偿了灵敏度的非线性误差,从而提高测量精度。

研究目的：

目前太阳辐照度绝对辐射计的定标精度随光功率的降低而下降,本文主要研究目的是提高太阳辐照度绝对辐射计的测量精度,从而提高定标精度。

研究方法：

通过理论分析以及实验测量的路线研究灵敏度非线性,通过修正灵敏度误差提高太阳辐照度绝对辐射计的测量精度。基于两点插值原理提出优化的测量方法。在各个辐射功率下测量实时修正灵敏度,得到灵敏度非线性的相对系统误差为2.2%,分析灵敏度非线性的影响。同时使用新方法以及传统方法测量辐射功率。

结果：

比对实验结果说明新方法将测量精度提高到0.1%,通过实时修正补偿了灵敏度非线性。

结论：

1）新方法可以显著提高地面比对实验的定标精度;

2）灵敏度非线性研究为优化太阳总辐照度监测仪的在轨定标精度提供了理论和实验依据。

关键词：测量精度;绝对辐射计;辐射定标;太阳辐照度

     

An automatic parameter calibration method for the SWAT model in runoff simulation

Runoff simulation is highly significant for hydrological monitoring, flood peak simulation, water resource management, and basin protection. Runoff simulation by distributed hydrological models, such as the soil and water assessment tool (SWAT) model which is the most widely used, is becoming a hotspot for hydrological forecasting research. However, parameter calibration is inefficient and inaccurate for the SWAT model. An automatic parameter calibration (APC) method of the SWAT model was developed by hybrid of the genetic algorithm (GA) and particle swarm optimization (PSO). Multi‐station and multi‐period runoff simulation and accuracy analysis were conducted in the basin of the Zhangjiang River on the basis of this hybrid algorithm. For example, in the Yaoxiaba Station, the calibration results produced an R² of 0.87 and Nash Sutcliffe efficiency (NSE) index of 0.85, while verification results revealed an R² of 0.83 and NSE of 0.83. Results of this study show that the proposed method can effectively improve the efficiency and simulation accuracy of the model parameters. It can be concluded that the feasibility and applicability of GA‐PSO as an APC method for the SWAT model were confirmed via case studies. The proposed method can provide theoretical guidance for many hydrological research fields, such as hydrological simulation, flood prevention, and forecasting.     

Carrier leakage and I/Q mismatch calibrated technique

The carrier leakage and I/Q mismatch calibrated technique based on the digital baseband for the direct conversion transmitter is described. The proposed technique only needs a calibration chain to detect mismatches, and then transmits them to the digital baseband, which completes the calibrated task. The proposed method is very simple in reducing die areas and power dissipation. Under TSMC 013μm CMOS technology simulation, the calibrated error of carrier leakage is less than 15％ and the error of I/Q mismatch is less than 65％．The measurement results indicate that I/Q amplitude mismatch is reflected at twice the input frequency. The calibrated chain gain range is 15dB with a 5dB step, and the bandwidth is 20MHz.     

1000kV主变压器调压补偿变压器现场试验技术研究

文章以1000k V特高压皖南站和淮南站主变压器为例,研究不同厂家主变压器调压补偿变差异性,在此基础上,介绍了调压补偿变压器现场试验项目,试验方法和试验注意事项。     

某机载雷达发射校正系统的EMC设计

因受载机平台内电子设备电磁干扰的影响,某机载雷达发射校正时存在通道相位漂移的现象,表现为同一通道相位多次测量偏差超过正常幅度值.在阐述发射校正系统工作原理的基础上,深入分析干扰的来源和机理,提出了综合运用屏蔽、接地、滤波等措施解决电磁兼容问题的具体方法,实现了雷达发射校正系统的可靠工作,为该类工程设计提供了参考.     

“大运行”体系下调控运行现场培训模式探讨

在电网调度管理工作中,现场培训是一项极其重要但又难以开展的工作。本文分析了“大运行”体系建设对调控运行现场培训的影响以及传统现场培训模式下的不足．结合青岛地区调度工作实际提出一种新的现场培训模式,该模式能够有效提升调控运行人员的业务素质水平,对调控运行人员现场培训工作具有指导意义。     

影响摄像机标定的摄像机模型研究

文章讨论了摄像机模型中各种参数因子对标定结果的影响,评价了采用仿真数据模拟方式对参数的精度影响.     

多种测井曲线校正方法在塔中顺9井区的应用

针对顺9井区柯坪塔格组声波时差和密度曲线失真严重的问题。首先建立了工区的区域岩石物理模板判断测井曲线的失真段,然后使用了经验公式法、多元线性拟合法和岩石物理建模法对声波时差和密度曲线进行了校正。对比发现,经验公式法和多元线性拟合法适用于井眼垮塌较小的井段,而岩石物理建模更适用于井眼垮塌较严重的井段。最后利用区域岩石物理模板和合成地震记录标定约束并检验了曲线校正的结果。结果表明这三种曲线校正方法在顺9井区的应用是有效的、可行的。     

舰载光电经纬仪方位基准标校方法

光电经纬仪工作前,要对经纬仪的方位测量基准进行标校,安装在陆地的经纬仪通常以正北作为方位测量基准。而舰载光电经纬仪的方位测量基准是舰载的艏艉线方向。专业的测量舰船设有独立的用于光电经纬仪的标校系统,普通的测量舰船没有设置单独的标校系统,只设有指示舰船艏艉线的平面基准镜,平面基准镜的法线方向即是舰船艏艉线方向。为了将舰船艏艉线平面基准镜的法线方向通过光路折转的方法转到光电经纬仪的光学主系统视轴上,设计一种方位基准标校装置。该标校装置由两个自准经纬仪和两个折转光管及辅助固定支架组成。标校时可在测量舰船上临时安装,标校工作结束后即可拆除,安装、拆除工作简单易行。折转光管的结构简单,便于保管运输。     

Simplified and efficient calibration of a mechanistic cutting force model for ball-end milling

Accurate evaluation of the empirical coefficients of a mechanistic cutting force model is critical to the reliability of the predicted cutting forces. This paper presents a simplified and efficient method to determine the cutting force coefficients of a ball-end milling model. The unique feature of this new method is that only a single half-slot cut is to be performed to calibrate the empirical force coefficients that are valid over a wide range of cutting conditions. The instantaneous cutting forces are used with the established helical cutting edge profile on the ball-end mill. The half-slot calibration cut enables successive determination of the lumped discrete values of the varying cutting mechanics parameters along the cutter axis whereas the size effect parameters are determined from the known variation of undeformed chip thickness with cutter rotation. The effectiveness of the present method in determining the cutting force coefficients has been demonstrated experimentally with a series of verification test cuts.