Experimental study of composite cold-formed steel C-section floor joists

Twelve large-scale slab specimens and twenty-two companion push-out specimens were tested to study the behavior and capacity of composite slab joists consisting of cold-formed steel C-sections and concrete. Four shear transfer mechanisms, including surface bond, pre-fabricated bent-up tabs, pre-drilled holes, and self-drilling screws, were employed on the surface of the flange embedded in the concrete to provide shear transfer capacity. Results indicated that specimens employed with shear transfer enhancements showed a marked increase in strength and reduced deflection compared with those relying only on a natural bond between steel and concrete to resist shear. Of the three shear transfer enhancements investigated, bent-up tabs provided the best performance at both the strength and serviceability limit states, followed by drilled holes in the embedded flanges. The use of self-drilling screws resulted in the lowest strength increase. The correlation of shear transfer capacity of push-out specimens with the ultimate capacity of large-scale specimens indicated that the average experimental flexural capacity of the slab specimens was approximately 1.16 times the average predicted value based on push-out test results.     

Zeolite synthesis from paper sludge ash with addition of diatomite

BACKGROUND: This study aimed to investigate the synthesis of zeolites from paper sludge ash (PSA) with added diatomite to remove both NH₄⁺ and PO₄^3? for water purification. The PSA had low Si and significant Ca contents. Four types of diatomite: white (T‐W) and brown (T‐B) from deposits of marine origin in Takanosu, and white (S‐W) and gray (S‐G) from lacustrine deposits in Shonai, were added to NaOH solution to increase the Si content and thereby synthesize zeolites with high cation exchange capacity (CEC). RESULTS: The order of the amounts of Si extracted from the diatomite to the alkali solution was S‐W > T‐W = T‐B > S‐G, which correlates with the amorphous SiO₂ content of diatomite. The original ash without addition of diatomite yielded hydroxysodalite with CEC of about 1.0 mmol g^?1. For all samples, the addition of diatomite to the solution yielded zeolite‐P with a higher CEC, but the addition of excess Si inhibited the synthesis of zeolite‐P, and the CEC of the product was low. A product with high CEC including zeolite‐P was obtained in a solution with around 500 mmol L^?1 of Si concentration, and had the ability to remove both NH₄⁺ and PO₄^3?. CONCLUSION: Diatomite has the potential for used as an additive for the synthesis of high CEC zeolite from PSA. The product with zeolite‐P exhibited relatively high CEC, capacity for NH₄⁺ uptake, and the ability to remove PO₄^3? by precipitation, which is preferable for water purification applications. Copyright © 2008 Society of Chemical Industry     

世界乙烯工业及其进展

阐述了世界乙烯产能需求现状，近扑扩能增产预测，乙烯原料分析以及乙烯生产的技术进展。     

Computation of Bearing Capacity Factor Nγ?Terzaghi’s Mechanism

A procedure based on K?tter’s equation is developed for the evaluation of bearing capacity factor Nγ with Terzaghi’s mechanism. Application of K?tter’s equation makes the analysis statically determinate, in which the unique failure surface is identified using force equilibrium conditions. The computed Nγ values are found to be higher than Terzaghi’s value in the range 0.25–20%, with a diverging trend for higher values of angle of soil internal friction. A fairly good agreement is observed with other solutions which are based on finite difference coupled with associated flow rule, limit analysis, and limit equilibrium. Finally, the comparison with available experimental results vis-à-vis other solutions shows that, computed Nγ values are capable of making a reasonably good prediction.     

钻井井架力学性能分析

钻井井架作为钻机系统设备中的关键部分,其力学性能直接关系到整套钻机系统的安全生产。文章推导了常用于分析钻井井架力学性能的理论,即线性屈曲、几何非线性和双重非线性理论。提出同时用这三种理论对钻井井架进行综合比较分析,从而合理地预见井架力学性能的方法。以A形钻井井架为例,进行了详细的分析,得到了井架的失稳形式、极限承载、破坏特征及薄弱部位,为钻井井架的设计、优化与评定提供了参考。     

文东油田连续气举优化配气数学模型建立及应用

针对连续气举在开发过程中出现的注入气利用效率低、综合效益差的问题，建立了供气能力有限时的优化配气数学模型，给出了解析法求解过程。文东油田现场试验表明，应用该技术可以实现连续气举井的合理配气，并提高油井产量，适合在油田推广应用。     

浅谈电梯选型应注意的问题

电梯选型配置问题是个十分有实际意义的话题。本文结合作者多年来检测检验电梯的经验，浅谈几点选型配置应注意的问题。     

Functional and sensory properties of chicken meat from spent-hen carcasses deboned manually or mechanically in Jordan

Samples of chicken meat from spent laying hens were obtained by four different methods: (1) manual deboning of whole carcasses; (2) manual deboning of skinned carcasses; (3) mechanical deboning of whole carcasses; and (4) mechanical deboning of skinned carcasses. The meat was packaged, frozen and stored at ?18 °C for up to 3 months. Functional properties studied were pH, emulsifying capacity (EC) and water‐holding capacity (WHC) and, in addition, pigment concentration was investigated. Sensory properties included aroma, colour, texture and overall acceptability, as judged by a trained panel using a nine‐point hedonic scale. Removal of the skin prior to deboning by either method gave significantly higher values (P < 0.05) for EC, while WHC values were not significantly different among the experimental treatments, despite higher pH values for mechanically‐deboned meat, with and without skin. Pigment concentrations were highest in meat from Treatment 4 and lowest for Treatment 1, but values for both methods of deboning were affected by the presence of skin. There were no significant differences between treatments for any of the sensory properties studied. Changes occurring in the meat during frozen storage are described.     

丙烯酸接枝聚丙烯纤维的结构与性能

本文研究了用化学引发剂引发丙烯酸接枝聚丙烯纤维的某些影响因素。红外光谱分析表明，丙烯酸接枝在聚丙烯大分子链的叔碳原子上。Ｘ－射线衍射和ＤＳＣ分析指出，纤维接枝后结晶度有所增加，接枝前纤维存在的β－变体转化成了α－变体，接枝纤维的吸湿性、离子交换容量和染色性随接枝率增加而增大。接枝纤维的力学性能有所下降。     

Decisive arrival law parameters and a general finite capacity queueing problem

This paper addresses the problem of finding the parameters of the arrival law which most significantly influence expected occupation and loss of a finite capacity queue. The input process is supposed to be ergodic and wide sense stationary. We show that it is mostly possible to fit an MMPP(2) to the decisive parameters of observational data. Numerical examples illustrate the importance of the decisive parameters, called key parameters, and also show the accuracy of the proposed fitting procedure. Finally, in the appendix we present the solution of the finite capacity queueing problem with Special Semi Markov Process (SSMP) arrivals and a general service strategy.