2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

HART通信协议在汽油机速度测量和监控方面的应用

首先介绍了HART通信协议及他的优点，然后介绍了HART通信协议在汽油机测速方面的软件实现。该软件主要采用目前流行的VB编程语言。可设计出界面友好、功能强大的测量和监控软件。     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

硅胶固载光敏剂的合成及其在反式维生素D3光敏异构化为顺式维生素D3中的应用

采用丙二酸作为连接,针9－蒽甲醇连接到硅胶上生成硅胶固载的光敏剂。利用此因相光敏剂分别在乙醇和甲苯溶液中敏化反式维生素D3。实验结果表明，此固相光敏剂能够有效地敏化反式维生素D3为顺式维生素D3的反应，并且非常容易从反应体系中分离出来。     

Niobium-containing catalysts—the state of the art

This review article is devoted to the materials containing niobium, which have been discovered or developed in the past few years and exhibit the potential application in heterogeneous catalysis. Niobium oxides and mixed oxides as well as sulfides, nitrides (oxynitrides), carbides (oxycarbides), and phosphates are considered. Among the catalytic processes in which Nb-containing materials were tested, liquid and gas phase oxidation is described in details, and the role of niobium in the prevention of the catalyst from SO₂ poisoning is mentioned.     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

基于C6711处理器cdma2000 1X系统前向信道信号的处理

在cdma20001x前向信道中,要对一段信号进行传送,一般选用QPSK调制,因为QPSK调制比QAM更适合噪音环境。采用TI6000系列的TMS320C6711芯片处理前向信道信号,可以对复杂性和实时性较高的信号做采集、量化、编码、调制等实时处理,主要功能通过软件编程实现,从而使系统具有结构灵活、可靠性高、可扩展等优点。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

机械力化学作用对低介硅灰石瓷料的相变和相组成的影响

采用X射线衍射仪(XRD)、差热分析(DTA)手段详细研究了由氧化物粉末制备硅灰石陶瓷时,机械力化学作用及后续热处理对硅灰石陶瓷相组成和相变过程的影响,分析了机械力化学在球磨过程中的作用机理主要是细化晶粒、使晶格畸变、晶格缺陷增多、非晶化和诱导低温化学反应。结果表明:高能球磨中的机械力化学作用能够有效地降低硅灰石陶瓷的烧成温度(11160~11220℃)。探明了经高能球磨的样品在烧成过程中的晶相转变规律。瓷料最终的晶相为单一的-硅灰石(高温变体)。     

连续波雷达测距中的解模糊技术

研究连续波雷达测距中的距离模糊问题，分析几种常用解模糊方法的性能，并讨论参差比的选取对测距范围的影响。