半刚性钢-混凝土组合节点受弯承载力的计算

在半刚性钢 -混凝土组合框架中 ,混凝土板中的纵向钢筋增加了节点的强度和刚度 ,但是 ,传统的设计方法往往忽略纵向钢筋的作用而采用简化的计算模型。因此 ,出于经济效益考虑 ,应该根据半刚性组合节点的实际受力性能建立更加准确的计算方法。这里详细介绍了考虑混凝土板纵向钢筋作用的半刚性组合节点受弯承载力的计算方法 ,计算结果表明 ,建议的公式与试验结果吻合良好 ,可供规范制定和工程应用参考。     

Failure load prediction of structural adhesive joints : Part 2: Experimental study

The objective of this study was to determine how the fracture of adhesive joints depends on elastic beam parameters describing the adherends and the applied loads. The basic specimen geometry was the cracked lap shear joint constructed of aluminium alloy with various adherend and bondline thicknesses. Loads were applied in different combinations of bending, tension and shear to generate a failure envelope for each adhesive and specimen geometry. It was found that crack propagation for precracked specimens occured at a critical strain energy release rate but was also a function of the G_I/G_II ratio and the bondline thickness. The experiments also showed that the loads required to propagate a crack in a precracked specimen were always lower than the loads required to break the fillet. Hence, by treating uncracked joints as being cracked, where the fictitious crack tip is assumed to coincide with the location of the fillet, a conservative estimate of the failure load is obtained.     

纳米SiO2粉体的制备与研究

纳米SiO2粉体的制备是以硅酸钠和盐酸为原料，添加适宜的稳定剂(非离子表面活性剂)和分散剂，在适宜的pH值和温度下，采用化学沉淀法合成。研究表明，要得到性能优良纳米的SiO2粉体，最佳工艺条件为：温度20～40℃，pH=6，反应液质量浓度P1=20g／L，P2=1．20g／L，反应时间15min。结果表明：制备的纳米SiO2粒径30～50nm，比表面积大，分散性好，质量优良，可达到产业化的生产。     

关于中压电缆网双环接线方式供电能力的分析

结合北京地区现阶段对相关技术的规定,以实际供用电方案为例,对中压电缆网双环接线方式的供电能力进行深入讨论。通过设计环网单元划分,发现某些条件下双环网供电能力可以得到进一步提升。     

电厂电气运行中常见故障分析及其应对措施探讨

为了保证电厂的生产效率,必须要分析电气的运行特征,确定电气故障发生的原因,综合考虑多方面因素,选择切实可行的措施解决问题。简要分析了电厂电气运行常见故障发生原因,并提出了相应的解决措施。     

我公司进行热电联产的可行性分析

大压差减温减压是能的严重贬值。根据公司供热现状，分析了热电联产的可行性，利用蒸汽余压发电后，再供生产系统各热用户，这样既节约了能源又缓解了集团公司用电紧张的局面，而且有相当可观的经济效益。     

Adhesive bonding of stainless steel water tubing

The use of an adhesive to bond stainless steel water tubing, allowing stainless steel fittings to be employed, is considered and compared with the more conventional use of compression or capillary copper fittings together with a soft solder. Tests carried out to determine environmental effects on adhesively bonded stainless steel tubing suitable for domestic water supply, and the strengths of these joints, are described. It has been found that acrylic anaerobic adhesives are suitable for bonding tubing carrying cold water, the joints attaining superior strength to the copper-soldered ones; a reasonable degree of flexing can also be tolerated. It would appear that certain selected adhesives may also be used in joints carrying hot water.     

直流电桥法测量电缆故障点的距离

迅速、准确地探测故障点的位置对保证故障电缆的及时修复有着重要意义。介绍了电缆故障的性质和直流电桥法测量电缆故障点距离的原理，着重阐述了几种常用的电缆接地故障的测量方法，并提出在实际生产、施工中，应根据具体情况选取合理的仪器及测量方法，迅速、准确地探测故障点的位置，以保证故障电缆的及时修复。     

Experiments of a prototype wind-driven reverse osmosis desalination system with feedback control

A prototype wind-powered reverse osmosis desalination system was constructed and tested on Coconut Island off the northern coast of Oahu, Hawaii, for brackish water desalination. The system has four major subsystems: a multi-vaned windmill/pump, a flow/pressure stabilizer, a reverse osmosis module, and a control mechanism. The feedback control mechanism, developed by this study, allowed this prototype system to be operated satisfactorily under mild ambient wind of 5 m/s or less. No auxiliary power source was needed. The system operational data showed that at an average wind speed of 5 m/s, brackish feedwater at a total dissolved solids concentration of 3000 mg/1 and at a flow rate of 13 1/min could be processed by this system. The average rejection rate of this prototype system was 97% and the average recovery ratio was 20%. The energy efficiency of the system was measured at 3 5%, which is comparable to the typical energy efficiency of well-operated multi-vaned windmills. Generally, the system's energy efficiency decreases as wind speed increases.     

Effects of apitong (Dipterocarpus spp.) extractives on bond strength development and curing rate of adhesives

Emulsion polymer isocyanate ( ), polyvinyl acetate ( ) and resorcinol-formaldehyde ( ) adhesives were used to produce single lap shear specimens using resinous and non-resinous apitong (Dipterocarpus spp.) timbers. Tests showed that joints made with highly resinous apitong were about 40% weaker than similar joints made with non-resinous apitong. The resinous apitong was treated with different solvents to yield five different extractives which were characterized by infra-red analysis. Apitong extractives were then added to and adhesives and joints made with buna (Fagus crenata), a timber known to be low in extractives and easy to bond. Joints prepared using extractive-containing adhesives were generally weaker than those made with the unmodified adhesives. RF adhesives containing extractives cured more slowly than unmodified . It is thought that the acidic nature of the extractives changes the pH of the system sufficiently to affect the curing mechanism