方波扫描路径确定声源声功率误差特性分析

改进了矩形测量面方波扫描路径测量声功率的误差模型 ,以单极子、偶极子及四极子声源为例 ,给出了扫描方向、测量面离声源的距离及扫描线的密度的选取对理论误差的分布图形。分析结果表明 :对选定的测量面 ,在扫描线密度小的情况下 ,通过调整声源离测量面的距离 ,可以在声源近处找到一个最优点或较优点 ,使理论误差为零或很小 ;在绝大多数情况下 ,沿测量面长边扫描误差比沿短边扫描小。     

Reducing Average and Peak Test Power Through Scan Chain Modification

Parallel test application helps reduce the otherwise considerable test times in SOCs; yet its applicability is limited by average and peak power considerations. The typical test vector loading techniques result in frequent transitions in the scan chain, which in turn reflect into significant levels of circuit switching unnecessarily. Judicious utilization of logic in the scan chain can help reduce transitions while loading the test vector needed. The transitions embedded in both test stimuli and the responses are handled through scan chain modifications consisting of logic gate insertion between scan cells as well as inversion of capture paths. No performance degradation ensues as these modifications have no impact on functional execution. To reduce average and peak power, we herein propose computationally efficient schemes that identify the location and the type of logic to be inserted. The experimental results confirm the significant reductions in test power possible under the proposed scheme.     

Effect of Additives on Magnetic Properties of High Frequency MnZn Power Ferrite

In keeping with the advance of more compact and more power-saving electronic equipment, the demand is increasing for smaller and more efficient switching power supply. Therefore, it is necessary to provide the adequate magnetic power ferrite materials to satisfy the demand. Such ferrite materials have to meet the following main requirement: 1) high initial permeability (μ i ); 2) high saturation magnetic induction (Bs); 3) high Curie temperature (Tc); 4) high electrical resistivity (ρ ); 5)…     

微波功率放大器预失真线性化技术分析

给出了两种基本形式的预失真线性化电路,对其工作原理和技术特点进行了分析。     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

Influence of a Jump in the Power of Laser Radiation on Its Measurement

Simulation and investigation of the effect of an isolated jump on realization of the unit of power of laser radiation and dissemination of the size of the unit are considered. Results are obtained by means of a newly developed algorithm that characterizes the behavior of the mean value of a signal and the standard deviation of a system as functions of the parameters of a jump in the power of laser radiation and the length and amplitude of the jump. If information concerning the time when a jump occurs is available, the proposed algorithm makes it possible to take into account how a jump affects the ultimate result of a measurement.     

液动旋冲接头冲击功测试方法研究

液动旋冲接头性能参数是旋冲接头设计的主要依据之一，如何对液动旋冲接头的参数进行检测是非常重要的工作。在分析和比较了测试液动旋冲接头性能参数各种方法的基础上，选择了冲击力法来进行破岩液动旋冲接头的性能参数测试，以YD系列测力传感器为检测元件，建立了一套比较完善的自动检测系统。分析了影响单次冲击功测试的因素，得出了测试旋冲接头的性能参数的影响规律。     

电源设备的功率因数校正技术

功率因数校正(PFC)技术能提高电源设备的电源利用率，减少谐波。文中介绍了功率因数的定义，功率因数校正技术及其应用实例。     

供电器可供放大器最大级数的计算

有线电视电缆网采用供电器进行集中供电，要计算一个额定容量的供电器可供放大器的最大级数，算式是很复杂的，而用VisaulFOXPRO6．0编写一个小程序，利用电脑对上述问题进行处理，就变得简单易用。     

TOPSwitch集成电路在DC/DC电源设计中的应用

文章介绍了PWM／MOSFET二合一的TOPSwitch系列集成电路及其在DC／DC电源设计中的应用，还介绍了基本反馈方式的DC／DC拓扑结构及其改进措施，并对由TOPSwitch集成电路构成的DC／DC电源进行了抗中子实验。