关于新疆热电厂职业危害分析与讨论

对比不同热电厂企业工人接触职业危害因素情况,分析原因,为在建或已建热电厂提供职业危害因素预防措施,降低企业由于设计、施工或管理方面原因造成后期运行过程中职业危害接触超标情况的发生。根据我室历年对新疆地区热电厂职业危害因素检测结果与评价报告的比较,找出不同热电厂职业病危害因素的共性及异性,分析不同设备、工艺及管理方式不同所造成职业危害因素检测结果的差异及原因。建议优化厂区工艺及土建设计;优化设备选型及原料选择运用现代化的管理手段,加强职业卫生管理体系宣贯的有效运作。     

Optimal power flow by BAT search algorithm for generation reallocation with unified power flow controller

Optimal power flow with generation reallocation is a suitable method for better utilization of the existing system. In recent years, Flexible AC Transmission System (FACTS) devices, have led to the development of controllers that provide controllability and flexibility for power transmission. Out of the FACTS devices unified power flow controller (UPFC) is a versatile device, capable of controlling the power system parameters like voltage magnitude, phase angle and line impedance individually or simultaneously. The main aim of this paper is to minimize real power losses in a power system using BAT search algorithm without and with the presence of UPFC. Minimization of real power losses is done by considering the power generated by generator buses, voltage magnitudes at generator buses and reactive power injection from reactive power compensators. The proposed BAT algorithm based Optimal Power Flow (OPF) has been tested on a 5 bus test system and modified IEEE 30 bus system without and with UPFC. The results of the system with and without UPFC are compared in terms of active power losses in the transmission line using BAT algorithm. The obtained results are also compared with Genetic algorithm (GA).     

Reduction of waste biosolids by RAS-ozonation: Model validation and sensitivity analysis for biosolids reduction and nitrification

Biosolids reduction model by return activated sludge ozonation was validated by simulating nitrification data compiled from our pilot-scale and the literature studies. Then, a global sensitivity analysis (GSA) was performed to identify influential and non-influential parameters for biosolids reduction efficiency, change in specific nitrification activity (SNA), and alteration to expected nitrification stability. In general, the model outputs were sensitive to operational and ozone reaction parameters, but not to biochemical parameters. For operational parameters, mainly temperature and initial solids retention time (SRT) influenced all model outputs. For biosolids reduction, increase in the degradability of the influent COD decreased the reduction efficiency. For SNA, the changes were highly dependent on the influent TKN/COD ratio. Our findings also imply that the stability of the nitrification process in ozonated systems should be enhanced at constant MLVSS for warm temperatures, but could be reduced at temperatures below 12 °C and aerated SRTs below 10 days.     

水泥窑余热发电系统用耐磨材料的研制与应用

本研究针对水泥窑余热发电系统的工作条件,根据耐磨材料的损毁机理,采用高铝矾土、煅烧氧化铝粉、黏土、硅微粉等为原料,以磷酸二氢铝为结合剂,以铝酸钙水泥为促硬剂,通过添加掩蔽剂和优化配料工艺,制备了水泥窑余热发电系统用耐磨材料,并对不同处理温度对耐磨材料的性能影响进行了分析。结果表明增强骨料与基质的结合能力有利于耐磨性的提高,磷酸及磷酸盐与氧化铝之间会随着温度的升高生成不同的磷酸铝相,都能够起到结合作用,比采用水泥结合更有利于提高材料在不同温度下的强度和耐磨性。使用结果表明,制备的耐磨材料施工性能优良,凝结硬化时间适当,强度高,抗冲刷性能好,在水泥窑余热发电系统中取得了良好的使用效果。     

Resistance reduction effect of potassium bismuth titanate doping in yttrium–manganese co-doped medium Curie temperature barium titanate lead free ceramics through improved synthesis process

Through improved synthesis process, resistance reduction effect of (K_0.5Bi_0.5)TiO₃ (KBT) doping in Y–Mn co-doped BaTiO₃ (BT) lead free ceramics was investigated. By different doping methods (doping K₂O, Bi₂O₃ and TiO₂ or synthesized KBT), medium Curie temperature (around 130 °C) lead free BT ceramics were obtained with ultra-low resistivity (13.84 Ωcm) with a temperature maintaining process at 700 °C. In this contribution, effect of sintering process and doping methods is discussed in detail.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

基于WiMAX通信网络的电源监控系统的构建

分析了全球微波接入互存(WiMAX)的技术特点和算法复杂度,探讨了其在电源监控系统中的应用,提出了基于Inter WiMAX Connection 2250技术的远程电源监控系统。在讨论WiMAX物理层算法的基础上,确定了以正交频分多址(OFDMA)模式为主体的物理层通信协议,提高了信道的利用率,抑制了码间干扰,为构建电源监控系统打下了良好的基础。     

Distributed wireless power transfer in sensor networks with multiple Mobile Chargers

We investigate the problem of efficient wireless power transfer in wireless sensor networks. In our approach, special mobile entities (called the Mobile Chargers) traverse the network and wirelessly replenish the energy of sensor nodes. In contrast to most current approaches, we envision methods that are distributed and use limited network information. We propose four new protocols for efficient charging, addressing key issues which we identify, most notably (i) what are good coordination procedures for the Mobile Chargers and (ii) what are good trajectories for the Mobile Chargers. Two of our protocols (DC, DCLK) perform distributed, limited network knowledge coordination and charging, while two others (CC, CCGK) perform centralized, global network knowledge coordination and charging. As detailed simulations demonstrate, one of our distributed protocols outperforms a known state of the art method, while its performance gets quite close to the performance of the powerful centralized global knowledge method.     

A Global Maximum Error Controller Based Nonlinearity Aware TPWL Method for Reducing Nonlinear Systems

Abstract

Model order reduction is a common practice to reduce large order systems so that their simulation and control become easy. Nonlinearity aware trajectory piecewise linear is a variation of trajectory piecewise linearization technique of order reduction that is used to reduce nonlinear systems. With this scheme, the reduced approximation of the system is generated by weighted sum of the linearized and reduced sub-models obtained at certain linearization points on the system trajectory. This scheme uses dynamically inspired weight assignment that makes the approximation nonlinearity aware. Just as weight assignment, the process of linearization points selection is also important for generating faithful approximations. This article uses a global maximum error controller based linearization points selection scheme according to which a state is chosen as a linearization point if the error between a current reduced model and the full order nonlinear system reaches a maximum value. A combination that not only selects linearization points based on an error controller but also assigns dynamic inspired weights is shown in this article. The proposed scheme generates approximations with higher accuracies. This is demonstrated by applying the proposed method to some benchmark nonlinear circuits including RC ladder network and inverter chain circuit and comparing the results with the conventional schemes.     

泛在电力物联网在北京经济技术开发区的应用探索

泛在电力物联网是物联网在电力领域的具体体现，建设泛在电力物联网是推进"三型两网"建设的关键环节，也是实现能源转型的必要手段。阐述了泛在电力物联网的定义，从供电公司角度出发，根据北京经济技术开发区实际情况，讨论了依托地区特点的泛在电力物联网实施策略和实际应用场景，分析了可能遇到的问题。得出结论：随着泛在电力物联网的深入建设，供电公司能够为电力客户提供多元化服务，提高客户满意度；地市供电公司能够依托泛在电力物联网开展更多电力相关业务；泛在电力物联网的安全性、实用性、有效性是发展面临的首要问题。