多孔挡板流化床还原UO3反应器模型的研究

针对ＵＯ＿３的Ｎ＿２还原反应建立了多孔挡板流化床反应器模型。将多孔挡板床的每一级视为具有相似的流动状态，每一级的上、下段称为稀、密相段，分别用鼓泡床和活塞流模型描述。该模型的计算值与￠６３ｍｍ的多孔挡板床Ｈ＿２还原ＵＯ＿３的热态实验值能较好的吻合。还预计了还原温度、操作气速和挡板结构参数对固相转化率的影响，为该类反应器的工业设计、放大和优化提供了依据。     

非方程灰色系统方法在长期水文预报中的应用初探

基于水文过程的复杂性和影响因子信息收集不完善这一基本事实，本文将流域水文系统视为含有灰元和灰信息的灰色系统，并初步实践了非方程灰色预报方法在长期水文预报中的应用。方法在一定意义上脱离了传统的以方程为中心的预报模式，它既考虑预报因子对预报量的不同影响程度，又不过分强调预报量与预报因子的具体相关函数形式，为长期水文预报提供了一种新思路。文中列出了实例，效果令人满意。     

离体肾脏保存实验研究

本文讨论离体肾脏生存机理研究的意义和方法，研制,成功的一种携带式快速和精确控制保存环境温度的脉动灌流型人工生命维持系统，采用微处理器进行实时数据采集，处理和非线性多模式采样控制，用以维持设定的环境参数和维持最佳生存条件，本文是采用猪肾为实验材料，进行多例离体猪肾的保存实验，研究有关环境参数和保养液成分对保存效果的影响，取得良好结果，实验性猪同种异体移植亦已获得初成成功。     

在役加氢反应器试验板脆化和氢损伤的测定与研究

充分利用了带主焊缝的役后试板，在国内首次开展回火脆化、氢介质下断裂韧性与疲劳扩展的研究，结果表明，加氢反应器焊缝有明显的脆化表现。同时，核查了反应器开停车升温速度和降温速度规定，以及确定了裂纹允许尺寸的参考数据，为今后安全运行提供了充分的依据。     

Φ76mm自动轧管机组穿孔机顶杆小车的改进

通过校核Φ７６ｍｍ自动轧管机组穿孔机顶杆小车的轴承寿命，提出了顶杆小车的改进措施，如重新选配合适的轴承型号，修改有关装配尺寸等。改进后，顶杆小车的使用效果良好。     

Influence of two-step process and of different stoichiometric ratios on morphologies generated in castor oil epoxy resins

Phase separation during polymerization was studied in a model system consisting of a diepoxide based on diglycidyl ether of bisphenol A (DGEBA), variable amounts of ethylenediamine (EDA) and the mass of castor oil (CO) necessary to obtain a mass fraction equal to 0-15 in a final system where the stoichiometric ratio of amine to epoxy equivalents, r, was equal to 1. A two-step polymerization process was performed by curing first a system with r = 0-5, during variable times before phase separation, and then carrying the system to r = 1. Thermodynamic analysis of samples with different r values led to a linear relationship between the Flory-Huggins interaction parameter and r. The concentration (P) and average size (D?) of dispersed-phase particles followed opposite trends, i.e. P increased while D? decreased, when either r was increased or the time of curing in the first step of a two-step process was decreased. This was explained by assuming that the competition between nucleation and growth was determined by the viscosity at the cloud point, η_cp. Low values of η_cp favoured growth over nucleation and led to fewer but larger particles.     

挟沙水流中沙粒对底壁湍流猝发的影响

本文在常规的边界层方程中保留了法向压力梯度项和增加了固粒对流体的使用项，结合Ｂａｔｃｈｅｏｌｒ对交界面提供的分析方法和小扰动稳定性理论，由理论分析和计算得到了包括沙粒之类的悬浮体的尺寸，比重，流动Ｒｅ数，两相速度差以及扰动波数与水流底壁湍流猝发角的关系，计算结果与Ｒａｓｈｉｄｉ等的实验结果相符。文中所得结果有助于进一步了解江河底部水流的流动特性以及泥沙的沉积和输运机理。     

Relaxation phenomena caused by equilibration of point defects

Relaxation phenomena due to equilibration of point defects in metals are reviewed. The relaxation effect in specific heat observed in tungsten and platinum confirms that in both cases the nonlinear increase in the high-temperature specific heat has to be attributed to point-defect formation. Relaxation phenomena observed by measurements of electrical resistivity and positron annihilation are also considered. The comparison of the data seems to be favorable for the conclusion that all the phenomena are of one origin.     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002