Control strategies for reactive batch distillation

A batch reactor may be combined directly with a distillation column by distilling off the light component product in order to increase the reactor temperature or to improve the product yield of an equilibrium reaction. The same amount of the light product should be removed as the amount being formed by the reaction at any time. A linearized model has been developed which describes the process behaviour satisfactorily for control analysis purposes. The controllability of a combined batch reactor/batch distillation column is found to depend strongly on the operating conditions and on the time during the run. In general, controlling only the reactor temperature (one-point bottom control) is difficult since the set-point has to be specified below a maximum value in order to avoid break-through of an intermediate component in the ditillate. This maximum value may be difficult to know a priori. For the example considered in this study, control of both reactor temperature and distillate composition (two-point control) is also found to be difficult due to large interactions in the column. As with one-point bottom control, the reactor temperature has to be specified below a maximum value. However, energy can be saved since the heat duty can be decreased with time. Controlling the temperature on a tray in the column (one-point column control) is found to give good performance for the given process with no loss of reactant and a high reactor temperature, although no direct control of the reactor temperature is obtained.     

Mixed Mode VLSI Implementation of a Neural Associative Memory

A mixed mode digital/analog special purpose VLSI hardware implementation of an associative memory with neural architecture is presented. The memory concept is based on a matrix architecture with binary storage elements holding the connection weights. To enhance the processing speed analog circuit techniques are applied to implement the algorithm for the association. To keep the memory density as high as possible two design strategies are considered. First, the number of transistors per storage element is kept to a minimum. In this paper a circuit technique that uses a single 6-transistor cell for weight storage and analog signal processing is proposed. Second, the device precision has been chosen to a moderate level to save area as much as possible. Since device mismatch limits the performance of analog circuits, the impact of device precision on the circuit performance is explicitly discussed. It is shown that the device precision limits the number of rows activated in parallel. Since the input vector as well as the output vector are considered to be sparsely coded it is concluded, that even for large matrices the proposed circuit technique is appropriate and ultra large scale integration with a large number of connection weights is feasible.     

微机型漏电保护装置的抗干扰措施浅析

本文针对微机型漏电保护装置在工业运行环境下,可能遇到的干扰进行了分析,并提出了从硬件到软件一系列行之有效的抗干扰措施。     

LW-601喷水织机长丝织物松紧档疵点的成因及对策

松紧档疵点是喷水织机长丝织物织造过程中常见病疵之一。通过分析LW -60 1喷水织机的送经和卷取装置的工作原理 ,从机械调整与维护、生产过程管理及工艺优化等方面探讨了其产生的原因 ,并针对性提出了实用对策     

用快切装置替代备自投装置提高厂用电安全可靠性

指出目前厂用电切换装置存在的不足，分析了快切装置的基本原理以及厂用电事故下的成功快切对电厂安全生产的意义，说明了在厂用电切换中尽快应用快切装置的必要性。     

井下沉砂器的研制与应用

针对以往机械防砂工艺存在防细砂困难、造价高和重复利用率低等缺点 ,根据旋流 离心分离原理 ,研制了井下沉砂器。沉砂器由上接头、二级滤砂管、筒体、中间接头、造旋臂、旋流体和下接头组成。中原油田分公司第五采油厂 2 2井次的现场应用表明 ,这种沉砂器可以分离大于 0 0 0 5mm粒径的细砂 ,防砂效果好 ,具有结构简单 ,安装方便 ,加工成本低的特点 ,可以保证出砂井的正常生产 ,延长检泵周期 ,节省作业费用     

大方坯连铸机离线检修设备对中台的改进与完善

介绍了大方坯连铸机离线设备对中台及样规的改进方案.改进后,大大缩短了设备检修时间,降低了工人的劳动强度.     

捞油车自动排绳控制装置

针对部分油田采用捞油的采油方式，介绍的自动排绳装置，是双通道化例闭环控制系统，特点是按照输入的给定、误差信号方向、大小变化，输出信号的方向、大小随之变化，自动跟踪，自动补偿，输出速度连续无级变速，可以手动和自动工作。     

螺旋焊管内涂层涂敷挥发份的清除

针对大口径螺旋焊管内涂层涂敷作业时，钢管内残留的涂料挥发份如何清除的问题，介绍了一种自行设计制造的内涂层涂敷挥发份吹除装置。