嵌入式消毒柜门内衬板拉深模具设计

通过对嵌入式消毒柜门内衬板工艺分析，确定其模具加工方案，同时对试模过程中存在的问题作进一步的剖析。     

冰箱门面板冲压工艺分析及模具设计

分析冰箱门面板的冲压工艺,介绍模具设计中应注意的问题及滚压式结构的特点     

Defect structure and chemical diffusion in nickel sulfide β-Ni3S2

The chemical composition, defect structure, and diffusion in nickel sulfide -Ni₃S₂ have been investigated in H₂S-H₂ mixtures containing between 1 and 65% H₂S between 560 and 700°C. Gravimetric, density, and X-ray studies were carried out. In the thermodynamically stable compound the ratio of Ni/S varied between 1.3 and 1.75. The X-ray examination showed a step change in the lattice parameter at the Ni/S ratio 1.4. A linear dependence of the density values (between 5.5 and 6.2 g/cm³) on the composition was observed. On the basis of the chemical composition and density measurements the number of nickel and sulfur atoms in 1 cm³ were determined. It has been shown that the Ni₃S₂ phase is defected in both anion and cation sublattices and that its chemical formula may be described as follows: Ni_3±yS_2x, where y 2x. It has been found that in the mixture containing 10% H₂S the process of defect formation is determined by their diffusion in the sulfide. The temperature dependence of the diffusion coefficient is described by the equation D = 13.15 exp(-30,000/RT) cm²/sec. No dependence of D on the sulfur partial pressure was observed, but this may be due to the relatively large uncertainties in the measurement of the diffusion coefficients.     

ANALYSIS OF DISSIPATIVE STRUCTURE IN MATERIAL COMMINUTION

ＡＮＡＬＹＳＩＳＯＦＤＩＳＳＩＰＡＴＩＶＥＳＴＲＵＣＴＵＲＥＩＮＭＡＴＥＲＩＡＬ　ＣＯＭＭＩＮＵＴＩＯＮＺｈａｎｇ；Ｚｈｉｔｉｅ（ＤｅｐａｒｔｍｅｎｔｏｆＭｅｃｈａｎｉｃａｌＥｎｇｉｎｅｅｒｉｎｇ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒｓｉｔｙｏｆＴｅ...     

Titanium in the rapidly cooled hypereutectic gray iron

The effect of titanium on the structure and properties of a rapidly cooled hypereutectic cast gray iron has been studied on the example of permanent mold (PM) casting. A microstructure study showed that titanium is a relatively strong element in controlling solidification structure by increasing undercooling and thus promoting type D graphite. The effectiveness of titanium additions depends on the base iron carbon equivalent (CE) with more pronounced changes in iron with a lower CE. The undercooling ability of the titanium decreases after exceeding a certain level. Increasing titanium from 0.09–0.12% slightly increases undercooling in iron with lower CE, but this effect was reduced in a more strongly hypereutectic iron. Alloying with titanium generally improves tensile strength, but the effectiveness of titanium additions also depends on the base iron CE range. Scanning electron microscope (SEM) studies revealed that most of the titanium-containing compounds were located in the metallic matrix: titanium carbides have been found in pearlite, while titanium nitrides and carbonitrides were located in ferrite. The presence of large amounts of extremely hard titanium-containing compounds, which often appear with steadite in a relatively high phosphorous content PM gray iron, amplifies the negative effect of titanium on machinability. This study suggests that for optimal combination of tensile strength/microstructure with good machinability, the titanium content in PM gray iron should not exceed 0.075%.     

系统失效的分支-界限分析法及其在桁架可靠性分析中的应用

本文首先介绍了系统失效的分支-界限分析法，然后以空间桁架系统为例用分支-界限分析法进行了可靠性分析。系统失效的分支-界限分析法直观、明了，适合对实际工程中的复杂系统进行可靠性分析。     

Ag-Cu-In-Sn合金的结构特性

借助金相、X光衍射及SEM方法研究Ag-Cu-In-Sn合金的结构特性及合金各组元在合金相中的分布规律,还讨论了某些相结构对合金力学性能的影响。四元合金的化学成分是(wt％)57～63Ag,17～23Cu,(20—x)In,xSn,其中:Ag+Cu=80wt％,In+Sn=20wt％,2≤x≤16。     

高线粗中轧机"浮动"检测结构设计及故障排除

为克服轧制中因机架锁紧功能降低而产生的机架沿轨座轴向移动的"浮动"现象,对其产生原因进行了分析,并通过改进锁紧装置结构及相关部件,使"浮动"故障得到预防和有效控制并及时排除。     

Influencing factors on elastic-plastic deformation of multi-layered surfaces under sliding contact

Stress distribution in the gradient multi-layered surface under a sliding contact was investigated using finite element method(FEM). The main structure parameters of layered surface discussed are total layer thickness,layer number and elastic modulus ratio of layer to the substrate. A model of multi-layered surface contact with rough slider was studied. The effect of the surface structure parameters on the elastic-plastic deformation was analyzed.     

汽车构造实验网络教学辅助系统设计

为切实提高汽车专业教学水平,建立全方位教学体系,设计基于网络的汽车构造实验教学辅助系统。系统充分利用学校现有计算机网络平台,利用多媒体和网络开发技术,开发或整合多媒体资料,开辟学习交流平台,依据课程学习规律和认知特点,建立起方便快捷、生动有趣的实验教学辅助系统。该系统基于现有教材,又高于教学内容,不仅对于传授汽车zai新技术和剖析专业难点,调动学习积极性,具有重要补充和推动作用,而且对于教学示范中心创建工作,也具有重要意义。