水泥散装无人值守系统数据管理

数据的实时性、准确性、全面性和灵活性是水泥散装无人值守高效、稳定、可靠运行的保证。本文主要以某水泥集团散装技改为例,讨论散装无人值守系统中运用的技术手段和对数据的管理。     

SOLUTION BEHAVIOUR OF VARIOUS ALLOYING ELEMENTS IN Ni_3Si

The solid solubilities of 15 common alloying elements added to the Ll_2-type intermetalliccompound Ni_3Si at 900°C have been estimated,and their substitution modes have been de-duced from the direction of solubility lobe of the compound.It is shown that the alloyingbehaviours in Ni_3Si are determined by both size and electronic factors,i.e.,the substitutionmode is governed by electronic configuration and solubility by the both.An interactionparameter is presented to describe quantitatively the influence of electronic configuration onsubstitution mode and the solubility limit can be successfully explained together with atom radius.     

IN-SITU OBSERVATION OF CRACK TIP DEFORMATION IN A DUPLEX STAINLESS STEEL

The development of dislocation structures in the plastic zone ahead of a crack tip has been in-vestigated in a duplex stainless steel during in-situ deformation experiments in a scanningtransmission electron microscope.It was found that the dislocation distribution wassignificantly different in the ferrite and in the austenite.In the ferrite grains,the dislocationsemitted by the crack tip may cross-slip out of the original slip planes and form a broad plasticzone.However,in the austenite,the dislocation free zone is small and the dislocations emittedby the crack pile up in its slip plane.The selection of slip systems at the crack tip depends onthe crack tip Schmid factors in both phases.But after large deformation,the selection of thesecond slip systems at the craek tip in austenite does not depend on the Schmid factors.     

顶头形状对穿孔毛管壁厚均匀性及能耗影响的研究

针对目前穿孔顶头形状研究所存在的问题,在实验室内就提高一次穿孔毛管的壁厚均匀性及降低能耗进行了系统的试验研究,初步研制成功一种新型的平头对心顶头。     

型材矫直工艺的改进

为提高型材矫直质量,防止矫后变形,对安钢小型厂300机组采取改进矫直工艺,增设矫后整形装置,改造矫直辊轴套,增设冷却水管路等措施,明显提高了角钢、槽钢的矫直质量。     

铸造工艺远程设计系统的实现

探索一种基于Internet的铸造工艺远程设计系统的开发方法。采用大口出流理论和均衡凝固理论作为浇冒口设计理论;以ASP．NET作为系统的开发工具,使用Access作为后台数据源,并用ADO．NET技术连接数据库;介绍实现系统主要功能的关键技术。将铸造工艺设计系统从单机平台转向Internet,提高了系统的共享度及升级维护的方便性,避免了系统的孤立和老化,并能实现多用户同时对系统的不间断使用。     

工业循环冷却水成套节水新技术在天津石化乙烯厂的应用

为解决天津地区水资源短缺的现状，通过应用先进的水处理药剂及自动监控技术，在天津石化公司乙烯厂成功地建成了高浓缩倍率冷却水处理技术示范工程，系统浓缩倍率从3倍提高到5倍以上，年节水量超过60万t。     

一种改进的超宽条带噪声消除算法

针对高光谱遥感图像中的超宽条带噪声干扰现象,在深入研究高光谱图像特点和条带噪声产生机理的基础上,提出了一种新的基于最小序列值、小波变换和矩匹配相结合的滤波算法（OWM算法）。该算法主要包括灰度对比度处理、最小序列值处理、小波变换系数归零处理和矩匹配处理等四个步骤。用实际的高光谱图像进行了一系列的验证比较实验,获得了好的实验效果。实验结果表明OWM算法不仅能够有效滤除高光谱图像中的超宽条带噪声,而且还具有较好的普适性。     

PIV Investigations of Flow Patterns in the Entrance Configuration of Plate-fin Heat Exchanger

Flow characteristics in the entrance of plate-fin heat exchanger have been investigated by means of particle image velocimetry （PIV）. The flow field was measured using the two-frame cross-correlation technique. Streamline and velocity contour graphs at different cross-sections were obtained in the experiment. The experimental results indicate that flow maldistribution in the conventional header is very serious, while the improved header configuration with punched baffle can effectively improve the uniformity. The flow maldistribution parameter in plate-fin heat exchanger has been reduced from 1.21 to 0.21, and the ratio of the maximum velocity to the minimum is reduced from 23.2 to 1.8 by installing the punched baffle. The results suggest room for the optimum design of plate-fin heat exchanger.     

广西饮用水水源地远程可视化监管系统设计

结合广西地区饮用水源保护的实际情况设计了一种新型的可视化远程监控系统可实现无人值守在线可靠监 控, 主要用于水源地现场可视化反馈并协助执法人员对水源地进行有效的监管保护, 获取各种周围环境信息, 并通 过执行器进行遥控。终端装置采用 STM32F103RBT6 单片机控制, 并通过 GPRS 网络接入局域网与联网的 PC 主 机进行网络通信, 配有 OV2640 摄像头与各种传感器以获取现场图片与各种参数。该设计在满足应用要求的情况 下, 尽可能降低设备成本。通过对传统监控方案改进, 新方案具有一定的潜在应用前景。