The design and test of dual/triple‐mode bandpass filter based on temporal coupled‐mode theory

In this article, the design and test of both a K‐band dual‐mode bandpass filter (BPF) pair and a K‐band triple‐mode BPF are presented based on N‐mode temporal coupled‐mode theory (CMT). The expressions of transmission and reflection responses are analytically derived. All the parameters in the expressions have clear physical meanings and are easily optimized to reach the required filter performance. Aided by eigenmode simulations, concrete structures of the three integrated BPFs are designed and optimized to approach the calculated physical parameters. After the fabrications and measurements of the three BPFs, extended upper/lower stopband with high stopband rejections are achieved, and by increasing the number of resonant modes, improved frequency selectivity and better passband flatness are obtained. The analytical analysis well predicts the simulation and measurement results, which provides an efficient way for BPF designs. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:609–622, 2016.     

Robust flat filtering DSP based control of the boost converter

The article deals with the design and implementation of a flat filter tracking digital controller for a boost dc-dc power converter. A highly perturbed switched boost converter circuit is shown to be efficiently controlled, in a trajectory tracking task for its non-minimum phase output, by means of a suitable linear filter, here addressed as a flat filter. Flat filtering is a natural robust version of generalized proportional integral control (GPIC) by which the effects of arbitrary time varying exogenous disturbances, unknown endogenous nonlinearities and un-modeled dynamics can be jointly attenuated in a conceptually similar fashion to observer-based active disturbance rejection control (ADRC) and algebraic identification based model free control (MFC) but: a) without using extended state observers and b) respecting the original system order in a time-varying simplified model while avoiding algebraic estimation techniques. The proposed control technique based on the TMS320F28335 digital signal processor chip is tested by means of realistic simulations and experimental setup.     

基于细菌觅食算法的多线圈电- 机械转换器双模控制技术研究

针对提升电-机械转换器快速响应特性的技术需求,提出了新型三线圈结构电-机械转换器。通过建立的电-机械转换器数学模型,提出采用细菌觅食算法来寻找时间最优解,并基于此方法设计了砰-砰与比例-积分双模控制器。分析与仿真结果表明,相对于传统单线圈电-机械转换器,采用双模控制器的三线圈电-机械转换器,其响应时间从8.5 ms缩短至2.5 ms,震荡和超调不超过5%,可知该技术能够实现响应特性,前景良好。     

输出本质安全型准谐振反激变换器分析

在给定的输入电压和负载变化范围内,分析了准谐振反激变换器的输入电压和负载电阻对其开关频率、输出纹波电压和峰值电感电流的影响,总结了其变化规律,得出了满足电气指标要求的电感和输出滤波电容最小设计值,使得最大输出短路释放能量最小。     

基于六脉波交交变频的闭环调压调速方法研究

针对六脉波交交变频调速技术在高频段存在各频级间转速差较大的问题,提出了一种基于六脉波交交变频的闭环调压调速方法。该方法在2个高频段之间设置多个电压等级,通过改变交交变频输出电压的大小,进行交交变频闭环有级调压调速。仿真和实验结果表明,该方法能够有效利用存储器空间,扩大交交变频调速范围,调速效果较好。     

双级矩阵变换器空间矢量调制策略改进

针对双级矩阵变换器空间矢量脉宽调制策略存在控制复杂度高、不能对双级矩阵变换器的输入功率因数进行调节的问题,提出了采用间接空间矢量调制策略的方案:①各PWM周期内直流平均电压为一恒定值,从而免去了逆变级调制系数的修正;②输入功率因数角可调。同时,利用参考电压和变换矩阵对该调制策略进行简化,使其能够更有效地控制无功功率和输出电压。仿真结果验证了该调制策略的正确性和有效性。     

雷达跟踪系统的数据显示

介绍用单片机与制导雷达显示器组成的数据显示系统的设计,并且将目标的高度以数字的形式在显示器上显示,缩短操纵员的训练时间,完成了旧系统的改造升级。     

基于FFMPEG的视频转换系统的模块研究

对互联网视频传播平台的应用现状进行了详细的分析,结合目前视频转换的应用现状,采用CSCW协同工作理论建立的视频转换系统．并对各个层次所采用的技术进行了深入研究,给出了一个基于FFMPEG技术的业务基础架构平台的具体实现。     

一种汽车防盗钥匙认证系统的可靠性设计

发动机防盗锁止系统具有良好的性价比和极高的安全性能,目前成为首选的汽车防盗装置。该系统的钥匙认证过程需要通过低频无线通信实现,易受汽车复杂环境的影响而无法正常工作。为设计高可靠性的钥匙认证系统,本文通过研究低频通信电路的特性以及分析导致通信失败的原因,提出了设计低频通信电路参数的方法,并利用该方法完成了一个具体的钥匙认证系统的设计,实验结果表明设计的钥匙认证系统可以满足在汽车复杂的环境下保证稳定通信的要求。     

电荷平衡式电压—频率转换器的原理及误差分析

单片集成V/F变换器广泛用于自动控制、数字仪表和无线电设备中,其功能用于完成电压和频率之间的转换.将电压量(或电流量)转换成频率信号后其抗干扰能力大为增强,并且应用极为方便.本文以AD652为例,阐述了电荷平衡式压频转换器的工作原理,重点分析了转换过程中的原理性误差和由器件带宽产生的高频误差,并求解出误差表达式.