一种用于检测转角、转速和转矩的新型多功能非接触式传感器

对一种基于纳米晶软磁合金的非接触式,用于测量转角、转速和转矩的多功能传感器进行了研究。介绍了传感器的结构和原理,推导出传感器的输出方程和灵敏度表达式。通过试验,分析了传感器激磁磁场强度对转矩测量精度的影响,并得出了最佳激磁磁场强度;在25℃～100℃范围研究了温度变化对传感器输出的影响,其零点温度漂移(25℃)为0.002%F.S/℃;在0～450 N.m范围进行转矩加载,得到了较高的测量灵敏度以及较低的线性度误差、重复度误差及迟滞静态误差;在500 r/min～3 523 r/min范围内,转速最大相对误差为0.60%。试验数据显示,该传感器的精度能够达到1.0%,对于一般工程应用是可行的。     

高速分组交换网络中调度器的设计

为了满足迅猛发展的网络业务对网络服务质量提出的更高要求,使用高速分组网络交换机中的队列调度器可以有效地提供高质量的网络服务。通过采用分级式队列调度和四种队列调度算法有效地实现了队列调度器的设计。并且深入地比较和分析了队列调度器中多种队列调度算法的优缺点,尤其是对DRR调度算法进行了优化和改进。最后。对所设计的电路进行了仿真验证和电路综合,结果表明该调度器可以满足网络对服务质量的更高要求,并且能够应用到高速分组交换网络的调度器设计中。     

关于饱和软土地基堤坝边坡稳定分析总应力法的讨论

在饱和的软土地基上修筑堤坝,由于孔隙水压力不易准确测定,需采用“φ=0”的总应力法进行稳定分析。这一做法在国外已明确纳入设计规范,在国内工程界较少受到重视,导致过高地估计了安全系数。本文首先系统地回顾了临界状态土力学中的伏斯列夫强度理论,在理论上阐述了饱和软土地基快速填筑时采用总应力法的原因,同时引用了Bishop和Bjerrum、美国联邦公路局、美国陆军工程师团与我国水电水利工程边坡设计规范的相关条文,确认在饱和软土地基采用总应力法进行稳定分析的合理性。以花敖泡土石坝和拉哇水电站围堰为工程实例,分别采用对土的固结不排水剪的两种做法开展稳定性分析,结果表明,直接将土的固结不排水剪强度指标ccu与φcu作为填筑后的强度参数,将严重高估其安全系数。因此建议正在修订的碾压式土石坝与边坡设计规范增加相应条文,并期望引起工程界对这一问题的重视。     

不同土性地基考虑 ＳＳＩ效应的隔震结构地震响应分析

为探究不同土性地基的ＳＳＩ效应对层间隔震结构影响机理与动力响应规律,选取一个典型层间隔震结构,对其简化并制作缩尺模型,采用振动台试验的方法,分别在硬土、软土这两种地基上单向输入4条地震波来研究模型的动力响应。结果表明:土体具有明显的放大效应,随着地基土由硬变软,隔震结构周期延长倍数降低。隔震结构在硬土地基上能发挥较好的减震效果,而软土地基上减震效果明显减弱。软土地基上塔楼的动力响应较硬土地基增大,塔楼容易成为薄弱部位,其抗震设计应重点关注。     

Protection switching schemes and mapping strategies for fail-operational hard real-time NoCs

Communication infrastructures designed for mixed-critical MPSoCs must provide isolation of traffic, hard real-time guarantees, and fault-tolerance. In previous work, we proposed the combination of protection-switching with a hybrid Time-Division-Multiplexed (TDM) and packet-switched Network-on-Chip (NoC) to achieve all three goals. In this paper, we present an FPGA implementation of such a NoC with all its features. We give synthesis results for the hybrid NoC, including the network interface, and show that our router uses over 32% fewer LUTs and registers than a competitive state-of-the-art router for mixed-critical MPSoC. We then explore different channel and task mapping strategies for critical applications which use protection switching and evaluate the effect these mappings have on the best-effort (BE) traffic in the system. Results show, that spreading out the critical traffic rather than naively dividing the system in critical and non-critical application domains is advantageous or even necessary in many cases and can allow for up to 13% more BE traffic. We give a comprehensive trade-off analysis of three protection switching schemes—1:n, 1:1, and 1+1—and show that 1+1 protection has less than half the worst case latency for critical traffic that 1:n and 1:1 protection have. At the same time, 1+1 protection, on average, only causes a 1.18% earlier saturation rate for BE traffic, which we consider to be affordable. We conclude that 1+1 protection is ideally suited for use in mixed-critical systems with high safety requirements.     

基于软测量的化工精馏过程推断控制策略

针对化工精馏过程产品成分无法在线检测及其用温度间接控制产品成分的常规控制策略存在着控制精度低的问题,提出基于软测量的精馏过程成分非线性串级推断控制策略。该控制策略首先提出核岭回归的实时软测量方法,即利用满足Mercer条件的核函数改进线性岭回归算法,实现精馏过程产品成分的在线检测;然后在此基础上,提出一种新的非线性串级推断控制策略,即副环采用常规的温度间接控制,主环采用基于核岭回归软测量的推断控制策略。通过Mejedell等建立的精馏塔动态模型分别对单端和双端成分非线性串级推断控制策略性能进行分析,仿真结果表明,与传统控制方案比较,新控制策略的控制质量有了较大提高,控制结构简单,易于实施。     

基于强跟踪滤波器的开关变换器故障诊断

Buck变换器又称降压变换器、串联开关稳压电源、三端开关型降压稳压器。广泛用于计算机、家用电器、控制系统和通信系统中的电源几乎都是开关电源,具有超快速负载动态响应、高功率变换效率、高功率密度、低电压、大电流的特性.开关变换器作为它的主要电路,故障率较高,对它故障诊断研究是有意义的。基于强跟踪滤波理论,给出了一种开关变换器电路故障实时诊断的一种方法。该方法以建立一种开关变换器电路状态空间模型为基础,利用强跟踪滤波器对电路状态及元件参数进行估计,当元件参数发生软、硬型故障时,根据强跟踪滤波器对元件参数的跟踪结果及修正的Bayes分类算法,可实时诊断开关变换器电路中的元件故障。仿真结果证明了该方法的有效性。     

基于TLM2．0的硬件虚拟平台设计

利用OVP（Open Virtual Platform）提供的模型创建基于TLM2．0的硬件虚拟平台,可以为嵌入式软件提供一个快速有效的开发环境,实现软件和硬件的协同设计。提早开发出的软件也可以对系统虚拟平台进行功能验证,分析系统性能,确定系统的最优架构。     

Contrast‐enhanced wide‐angle high‐speed polarization modulator for active‐retarder 3‐D displays

Abstract— A contrast‐enhanced wide‐angle high‐speed polarization modulator for active‐retarder 3‐D displays is proposed. By using a double liquid‐crystal‐cell structure together with a dedicated driving scheme and an external quarter‐wave retarder, a high‐performance modulator can be realized, resulting in minimized brightness loss and low cross‐talk levels in fast‐refresh time‐multiplexed 3‐D displays.     

OAZE: A network-friendly distributed zapping system for peer-to-peer IPTV

IPTV systems attracting millions of users are now commonly deployed on peer-to-peer (P2P) infrastructures and provide an appealing alternative to multicast-based systems. Typically, a P2P overlay network is associated with each channel, composed of users who receive, watch and redistribute this channel. Yet, channel surfing (aka as zapping) involves switching overlays and may introduce delays, potentially hurting the user experience when compared to multicast-based IPTV. In this paper, we present a distributed system called OAZE (Overlay Augmentation for Zapping Experience) which speeds up the switching process and reduces the overall cross-domain traffic generated by the IPTV system. In OAZE, each peer maintains connections to other peers, not only in a given channel, but also in a subset of all channels to which the associated user is likely to zap. More specifically, we focus on the channel assignment problem, i.e. determining, in a given P2P overlay, the optimal distribution of the responsibility to maintain contact peers to other channels. We propose an approximate algorithm providing guaranteed performances, and a simpler and more practical one. Our experimental results show that OAZE leads to substantial improvements on the connections between peers, resulting in less switching delay and lower network cost; it then represents an appealing add-on for existing P2P IPTV systems.