应用在地下工程施工中的新技术（Ⅱ）

为有效保护地面上的生态环境，开发利用地下空间资源并营建新世纪的地下水城，在新的21世纪里将会建造更多的地下工程以满足人们生产生活的各种需要。文中介绍了地下工程施工中采用的逆作法、盾构法、新奥法、沉管隧道、顶管工程和大型沉井施工新技术，供同行们参考应用。     

微电量测量中信号的拾取和放大

本文介绍了静电计级运算放大器在工业微电量测量中的应用,并且给出了实际的电路结构和相关的噪声解决办法。     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

雁翎油田注氮气提高采收率工艺技术

在现有的提高采收率方法中,注气驱是应用较广、效果较好的方法,特别是注氮气驱由于其气源广泛、价廉经济、无腐蚀性,以及要求的油藏地质结构特征和原油的物理性质等因素的变化范围广泛等特产,这种提高采收率的方法应用的最为普及,代表了目前提高采收率的发展方向。结合雁翎油田实例,简要介绍了注氮气提高采收率的机理、注气井组建设、制氮工艺及注气后的采油完井方式、方法。     

钨铜合金药型罩及其性能

钨铜合金药型罩的应用可以提高射流对均质钢靶的侵彻能力.这一提高得益于射流密度的提高以及断裂时间的延长. 本文对钨铜合金射流及其断裂形态通过X光照像进行了研究.它的旋转效应及其炸高特性也进行了实验研究. 钨铜合金药型罩的威力实验在φ30 mm的破甲弹上进行.在相同装药条件下与紫铜罩相比,威力提高20～30%.     

定量电子晶体学硼对Ni3Al的电荷密度分布的影响

阐述了定量电子晶体学测定晶体电荷密度分布的基本原理和方法，不足之处和改善途径。以硼对Ｎｉ３Ａｌ的电荷密度分布的影响为实例，介绍了定量电子晶体学在研究晶体电子结构方面的应用前景。     

Silver Electrodeposition from Photographic Processing Solutions

This paper describes the parameters that are important in the industrial practice of silver removal from photographic fixers. The experiments were performed under potentiostatic control using synthetic solutions. The current efficiency was analysed as a function of the cathodic potential taking into account the deposit quality. A cathodic potential of ?0.5 V against a saturated calomel electrode is recommended. The conditions to prevent the darkening of the electrodeposit were investigated. The determination of silver concentration in the solution was made by direct potentiometry. The results obtained with synthetic fixers were corroborated by making the silver deposition from commercial fixers in an electrochemical reactor with rotating cylinder electrode intercalated in an electrolytic flow circuit in order to simulate practical conditions.     

振动采油工艺在稠油区的实验研究与应用

在天然地震的影响下,油井产量发生波动,使人们受到启示,从而引进了振动采油工艺技术。本文对振动增产的机理进行了探讨,指出振动增油机理在于加快地层中流体的流速;改变储集层内油、气、水的重新分布;改变岩石表面润湿性,有利于清除油层堵塞,提高渗透率。通过分析两个试验区的振动采油效果,总结出在不同扰动力、不同激振频率、不同振动周期下的增产效果和规律,对振动采油的实施具有一定的指导意义。     

Creep of aromatic polyamide fibres

Creep of Kevlar 29, Kevlar 49 and PRD 49-III fibres was investigated. The fibres exhibited transient creep and the strain-time relationship was represented by a logarithmic time law. The creep strain recovered with time when the load was removed. Upon reloading to the same creep stress the strain-time relationship was again logarithmic but the creep rate was reduced. Modulus measurements were made during the creep test and these showed that the modulus increased with time. This result indicated a crystallite rotation mechanism which could account for the experimentally observed creep strain. Creep in PRD 49-III fibres exhibited a small temperature dependence over the temperature range 20°C to 150°C. The apparent creep activation energy was consistent with the range of values reported for hydrogen bonding. This suggests one possible creep mechanism in which the combined action of stress and thermal activation causes rearrangement of intercrystalline bonds in the crystallite boundaries resulting in boundary creep. Boundary creep allows crystallite rotation which produces the macroscopic creep strain. Boundary creep is discussed in terms of the fibre morphology and a model of delayed elasticity.     

Spontaneous emulsification aspect of enhanced oil recovery

Recent studies have suggested the possibility of spontaneous emulsification as a mechanism for enhanced oil recovery (EOR). The discussions have, however, remained essentially qualitative. A study was therefore undertaken to estimate quantitatively the contribution of spontaneous emulsification as an EOR mechanism. The tests were conducted on several bulk liquid/liquid systems as well as by displacement experiments in unconsolidated synthetic sand packs. Spontaneous emulsification was found to be a mechanism for EOR: the estimated extra contribution to EOR due to this mechanism was found to be significant in laboratory scale displacement experiments. Tertiary recovery was always greater when spontaneous emulsification was evident than otherwise. Results of tests on bulk liquid/liquid systems indicate that the occurrence or absence of spontaneous emulsification can be correlated with the values of ‘partition parameter’. It may be concluded that higher oil recoveries may be achieved in chemical EOR processes where interface mass transfer (and the accompanying spontaneous emulsification) occurs. The evaluation of efficiency of residual oil mobilisation through the capillary number theory (with and without spontaneous emulsification) is also discussed. Displacement tests with spontaneously emulsifying systems showed that residual oil left behind a conventional waterflood was mobilised in a range of capillary numbers much less than that which applies to low-tension waterfloods.