基于PLC网络测控的炉外喂丝精炼系统

论述了基于PLC网络测控钢包炉外精炼系统的工作原理、硬软件设计和主要功能。分析了基于SIEMENS S7-400和s7—300型PLC网络测控，以及SIEMENS HMI TP-170A人机界面及其操作的设计方法。     

改善烧结法碳酸化分解产品质量的措施

本文简要阐述了提高氧化铝质量的必要性和紧迫性，并从烧结法碳酸化分解工艺着手，简介了碳酸化分解的工艺过程，同时从理论上分析了铝酸钠溶液碳酸化分解过程的变化规律，结合影响碳酸化分解产品质量的多种因素的试验结果，提出了碳分分解温度、分解时间、晶种特性和晶种添加量等是影响碳分产品质量的重要因素。     

电渣熔铸渣池热电场有限元模拟的前置处理

对电渣熔铸渣池进行了热电场有限元模拟的前置处理,建立了电渣熔铸渣池热电场数学模型,定义了以自耗电极、渣壳、水冷结晶器、渣池为对象的计算区域.借助大型有限元软件ANSYS,对计算区域进行了合理的单元、插值函数选取以及网格划分,研究发现渣池存在两个区域:一是温度很高、电流密度很大且分布很不均匀的小区域,位于自耗电极端部附近,为高热源区,另一是电流密度小且分布几乎均匀的大区域,为低热源区.     

稀土在铜及其合金缓蚀剂中的研究

通过失重悬挂法和中性盐雾等腐蚀试验，研究了多种添加剂对铜及其合金的缓蚀作用，结果表明：在BTA溶液中加入一定量的有机羧酸和和稀土RE（IV）盐后，由于三者的协同效应，显著提高了钝化膜的性能。     

高强度高韧性球铁曲轴的生产

研究了合金化，二次孕育，热处理工艺及圆角滚压对球铁曲轴性能的影响，经实际生产验证，此工艺可使抗拉强度超过800MPa，伸长率超过5％。     

Research and Applications of Semi-solid Processing

Since it was pioneered by Flemings and otherresearchers [11, the semi-solid metal processingtechnique has been widely stUdied in the world.Especially in the past decade, SSM as a newproduct forming technique has been rapidly developed and put into commercial applications[2, 31. In recent years, with the development ofthe ado-industry of China, a lot of researchwork on SSM has been done, including the preparation of slumes, reheating and thixoforming[Al6]; moreover, great achievements have …     

晶闸管式等离子弧切割机的使用与维修

本文介绍了晶闸管式等离子弧切割机的操作原理、使用和维修技术。     

Microstructural evidence for short-circuit oxygen diffusion paths in the oxidation of a dilute Ni-Cr alloy

A comparative study of high-temperature oxidation of Ni containing 1 at.% Cr and pure Ni was carried out. Instead of the conventional kinetics study using thermogravimetry, a microlithographic marker experiment was designed. Observation of the markers using cross-sectional TEM and SEM has revealed striking differences in the scale morphology, microstructures, and oxidation mechanisms between pure Ni and the Cr-doped Ni substrates. In particular, the results suggest that a small addition of Cr promotes significant inward transport of oxygen. Marker experiments revealed that NiO grown on pure Ni is wholly attributable to outward-cation diffusion. In contrast, NiO grown on Ni–1 at.% Cr exhibited formation of a substantial inner layer having a submicron grain size, established by the markers to have formed from oxygen ingress. For pure Ni, voids were observed to be distributed only within oxide grains. In contrast, for Ni containing 1 at.% Cr, elongated pores formed extensively along oxide-grain boundaries. Formation of new fine-grain oxide in these pores was observed to have sometimes completely resealed the void. It is, therefore, proposed that the transport of oxygen in the case of oxide scale grown on Ni–1 at.% Cr occurs via voids (pores) formed by vacancy coalescence at the grain boundaries.     

埋弧自动焊在大口径钢卷管焊接上的应用

为把埋弧焊应用在大口径钢卷管焊接上,分析了焊接工艺设计、焊接工装设计和纵缝、环缝焊接的施工要点,经过实际施工验证了这种方法是成功的,效益是高的。     

压铸模具型芯变形失效的研究分析

压铸模具的型芯变形失效很容易造成铸件的成批量报废.文中对于一失效型芯进行了分析研究,结果表明,其弯曲变形是由于受到不断循环的热作用及金属液的冲击所造成的微小变形积累造成的;同时,型芯的硬度在不同的部位均有下降,其中在冲击部位下降幅度最大.型芯在与铝液接触的表面会形成过渡层,圆形的型芯横截面会发生变形.采取有效的措施是可以避免田型芯弯曲变形所造成的铸件成批量报废的.