冲击腐蚀磨损系统中影响因素的正交分析

用改进的MLD-10型冲击腐蚀磨损试验机，对不同条件下的冶金矿山用低碳高合金钢的冲击腐蚀磨损性能进行了试验。用正交分析法研究了磨粒，冲击功和pH值在低碳高合金钢冲击腐蚀磨损过程中的作用。结果表明，磨粒在冲击腐蚀磨损过程中对材料的影响最大，其次为冲击功，pH值的影响最小。     

钛基复合材料激光熔覆层显微组织及其强化机制

利用激光熔覆技术在Ti-6A1-4V合金表面制备了TiC增强钛基复合材料涂层，复合材料的硬度明显高于基体，平均硬度可达940HV0.2。对复合材料的显微组织分析表明：TiC增强钛基复合材料的强化机制以细晶强化和弥散强化为主。     

双金属复合板带可逆冷轧有限元模拟

本文应用ANSYS有限元软件分析了热轧复合的不锈钢复合板在冷轧过程中的变形特性和界面上应力应变分布 ,分析确定了界面结合强度 ,以及确定成卷可逆带张力冷轧时的最大道次压下量值。用 3D FEM模拟了接触表面上的应力 ,计算出总轧制压力 ,与理论公式进行了对比。     

AZ91D镁合金在北京地区的大气腐蚀行为研究

利用室外大气暴露试验，研究了AZ91D镁合金在北京地区的平均大气腐蚀速率，并与相同条件下A3钢的大气腐蚀情况进行了对比．采用扫描电镜(SEM)、X-射线衍射(XRD)、X射线能谱(EDS)以及红外光谱(IR)等多种现代表面分析技术对腐蚀产物的形貌、组成、结构等进行分析，与A3钢相比，AZ91D镁合金具有良好的耐大气腐蚀性能，具有局部腐蚀的特征。     

Deposition of cerium contained conversion films on LC4 alloy with square wave pulse method

Cerium contained conversion films were deposited on LC4 aluminum alloy using square wave pulse (SWP) in aCeCl3 solution with KMnO4 as the oxidant. Energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM) were adopted to study the composition and the morphology of the film. It is found that the film is composed of Al, Zn, Cu,and small amount of cerium. The polarization curves of the specimens treated with SWP technique measured in 3.5% (mass fraction) NaCl solution reveal that the film thus formed inhibits both the anodic and cathodic process of the corrosion of the specimen. The immersion tests of treated specimens in 3.5% NaCl solution indicate that the corrosion resistance of the SWP treated specimen is better than that of the untreated and is equivalent to or even better than that of the traditionally electro-chemically treated specimens.     

High cycle fatigue and fracture behavior of 2124-T851 aluminum alloy

The high cycle fatigue properties and fracture behavior of 2124-T851 aluminum alloy were investigated roundly, including the fatigue crack growth rate, fracture toughness and fatigue S--N curve. Furthermore, the fatigue crack growth rate was analyzed by fitting the curves. And the microstructure of the alloy was studied using by optical microscopy, transmission electron microscopy and X-ray diffractometry, scanning electron microscop1/2 The results show that the fatigue strength and the fracture toughness of 2124-T851 thick plate are 243 MPa and 29.6 MPa.m at room temperature and R=0. 1, respectively. At high cycle fatigue condition, the characteristics of fatigue facture were observed obviously. And the higher the stress amplitude, the wider the space between the fatigue striations, the faster the rate of fatigue crack developing and going into the intermittent fracture area and the greater the ratio between the intermittent fracture area and the whole fracture area.     

Effect of heat treatment on thermal stability of Ti40 alloy

Five new heat treatment processes were designed, which were divided into three groups by their characteristics. The microstructures and mechanical properties of the alloy after the five heat treatments and thermal exposure at 500, 550℃ for 100 h were tested. The results indicate that a little differences exist in the performance of mechanical properties at room-temperature after the five heat treatments, and the thermal stability is the key factor for determining heat treatment process. Among the three groups of heat treatment processes, the best thermal stability is achieved after the first group of heat treatment. After annealing treatment at intermediate temperature, some defects and uneven grain boundaries are remained, which leads to the reduction fractions of precipitations on unit grain boundary and the harmful effect of precipitations on grain boundary is weakened. The process of annealing at 650 ℃for 4 h is recommended the best heat treatment process for Ti40 alloy.     

真空熔炼AZ91镁合金过程中Mg元素的蒸发行为

在真空Ar气氛中熔炼AZ91镁合金，测定了不同精炼温度下Mg元素的蒸发速率。结果表明，随着精炼温度的升高，Mg元素的蒸发量增大。通过计算可知，Mg的蒸气压是Al的10^9倍，是Zn的46倍，因此主要是Mg的蒸发而导致合金其他元素含量升高。XRD分析表明，蒸发物是Mg元素。结合Mg元素的蒸发机制，在该试验条件下推导出Mg元素蒸发率的计算公式以及Mg元素的表观传质系数、蒸发率与精炼温度的关系，计算得出Mg元素蒸发率为0．86×10^-3-1．35×10^3g／cm^2·s，Mg元素的表观传质系数在2×10^-5-24×10^-5cm／s范围内。     

坯料外形对镁合金矩形盒拉深成形的影响

用商业有限元软件模拟了在同一套模具和成形条件下不同毛坯外形的镁合金矩形盒拉深成形过程．依据数值模拟结果，分析了不同坯料外形对镁合金矩形盒拉深成形的影响。结果表明：使用矩形圆角坯料比其他坯料的成形性能好。     

用双层辉光等离子法在钛表面制备的Ti-Pd合金层性能研究

采用双层辉光等离子冶金技术在纯钛表面制备了Ti—Pd合金层。其深度大约为90μm，Pd含量呈梯度变化，并出现了TiPd3，TiPd2，Ti2Pd3，Ti3Pd5，TiPd，Ti4Pd等6种化合物相和Pd相。合金层在100℃的NaCl饱和溶液＋HCl溶液以及40℃的8．6％H2SO4溶液中的耐缝隙腐蚀性能优于Ti0．2Pd合金；在室温80％H2SO4的溶液中，腐蚀速率仅为0．682mm／a，是Ti0．2Pd合金的18．2％：在室温30％HCl的溶液中，表面Ti—Pd的腐蚀速率仅为0．004mm／a，是Ti0．2Pd合金的12．5％。