Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.     

Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.     

Drying of Prone to Twist Boards in a Pre-Twisted Position

A method to minimize twist has been investigated; i.e., drying the boards in a pre-twisted position. It has been found that Norway spruce boards can be deformed toward straightness by this method. The force exerted by a board on its holders during drying in a pre-twisted position has been measured. When the variation in torsional stiffness as a function of temperature and moisture content is accounted for, it is found that a creep deformation of the board occurs both during the drying phase and the cooling phase. In addition to mechano-sorptive creep, a deformation released by a change in temperature also seems to occur.     

Stability of large-scale coal-fired MHD channels

Stability of large-scale coal-fired MHD channels is studied by (1) linearized stability analysis, and (2) time-dependent 1-D analysis. The channel length is 15 m with 600 electrode pairs, and the output power ranges from 220.6 MW through 258.7 MW. Linearized stability analyses show that the Faraday channels operated with fixed loading resistance are stable, whereas the two waves of u and u–a (u, a: gas and sound velocity) become unstable in the Faraday channel with fixed loading factor. Two waves of u and u–a are unstable in the diagonal channel with fixed loading current and the u + a wave becomes unstable in the diagonal channel with fixed electrode current. Time-dependent one-dimensional analyses indicate that the Faraday channels with fixed load resistance are smooth without growth of fluctuation. The diagonal channels with fixed electrode current are smooth with no fluctuation, though the linear theory indicates that the u + a wave is unstable. The diagonal channel with fixed load current suffers large disturbance along the latter half of the channel, being consistent with the linearized analysis which indicates that the u - a and u waves are unstable.     

Thermal stability and high-temperature wear of Ti–TiN and TiN–CrN nanomultilayer coatings under self-mated conditions

Ti–TiN and TiN–CrN nanomultilayers were thermally stable retaining uniform and sharp layer interfaces up to 24 h at 773 K, without any oxidation or phase transformation accompanying each individual layer. Decreasing the multilayer spacing resulted in an increase in the hardness in both cases. The coating hardness was found to be independent of the substrate type, when applied on HS718, Ti64 and HCHCr substrates. In scratch testing, the multilayers displayed a better resistance to the onset of failure, as compared to the monolayer TiN. The substrate plasticity played an important role in determining the coating failure mode. Self-mated wear tests revealed the CrN–TiN system to exhibit the best wear behaviour, both at room temperature and at 773 K. The Ti–TiN coatings are more accommodative with all three substrates, as compared to TiN–CrN and TiN.     

The role of the surface free energy in the selection of a suitable excipient in the course of a wet-granulation method

Pellets containing metronidazole were produced in a centrifugal granulator, with hydroxypropylcellulose (Klucel LF®) as binding agent, and corn starch, microcrystalline cellulose (Vivapur 101®) and lactose as excipients. The wettability of the pharmaceutical powders was assessed by means of contact angle measurements, and the dispersive and polar surface energies were determined. The spreading coefficients, the work of adhesion and the work of cohesion were calculated and correlated with the pellet properties (friability, bulk and tapped density, and porosity). The aim was to investigate the role of the surface free energy of one- and two-component powder compositions in pellet production. The interactions between the particles were found to be connected with the measured pellet parameters. It was concluded that, in the course of the growth of the pellets, the particle sizes of the pharmaceutical powders and the interactions between them are important. If the work of cohesion of the binder is lower than the work of cohesion of the substrate and the work of adhesion, then the optimal amount of the binding agent is that which coats the particles uniformly in minimal quantity and in continuous layer.     

Transformation of β-Ni(OH)2 to NiO nano-sheets via surface nanocrystalline zirconia coating: Shape and size retention

Shape and size of the synthesized NiO nano-sheets were retained during transformation of sheet-like β-Ni(OH)₂ to NiO at elevated temperatures via nano-sized zirconia coating on the surface of β-Ni(OH)₂. The average grain size was 6.42 nm after 600 °C treatment and slightly increased to 10 nm after 1000 °C treatment, showing effective sintering retardation between NiO nano-sheets. The excellent thermal stability revealed potential application at elevated temperatures, especially for high temperature catalysts and solid-state electrochemical devices.     

Automated procedure to determine the thermodynamic stability of a material and the range of chemical potentials necessary for its formation relative to competing phases and compounds

We present a simple and fast algorithm to test the thermodynamic stability and determine the necessary chemical environment for the production of a multiternary material, relative to competing phases and compounds formed from the constituent elements. If the material is found to be stable, the region of stability, in terms of the constituent elemental chemical potentials, is determined from the intersection points of hypersurfaces in an (n−1)$(n-1)$-dimensional chemical potential space, where n$n$ is the number of atomic species in the material. The input required is the free energy of formation of the material itself, and that of all competing phases. Output consists of the result of the test of stability, the intersection points in the chemical potential space and the competing phase to which they relate, and, for two- and three-dimensional spaces, a file which may be used for visualization of the stability region. We specify the use of the program by applying it both to a ternary system and to a quaternary system. The algorithm automates essential analysis of the thermodynamic stability of a material. This analysis consists of a process which is lengthy for ternary materials, and becomes much more complicated when studying materials of four or more constituent elements, which have become of increased interest in recent years for technological applications such as energy harvesting and optoelectronics. The algorithm will therefore be of great benefit to the theoretical and computational study of such materials.     

种子法制备聚合物乳液技术的进展

从建筑乳液的生产现状、自生种子法与外加种子法的区别、种子乳液的特点及外加种子法生产的乳液特性等方面介绍了种子法制备乳液技术的进展。     

气雾型自动喷漆中助剂的应用

分析了气雾型自动喷漆中影响沉降，分散稳定性的主要因素，研究了助剂的应用及工艺改进等解决方法。