蒸汽减压站自控系统的巧设计

蒸汽是石油化工装置中最重要的物料。随着石油化工工业的迅猛发展 ,蒸汽在其中扮演着越来越重要的多重角色。因此 ,对蒸汽系统的平稳控制 ,对石油化工生产装置平稳、高效地运行是至关重要的。传统的蒸汽减压站自控系统基建投资大 ,紧急情况下靠人工手动操作稳定蒸汽压力系统 ,往往造成生产的波动或大面积的停车。针对传统蒸汽减压站自控系统的弱点 ,提出蒸汽减压站自控系统的优化设计方案 ,该方案得以在大型生产装置成功应用。新方案不但节省了大量的基建投资 ,而且取得了良好的生产效益     

合成氨扩能改造中锅炉存在的问题及采取的措施

针对天脊集团年产30万t合成氨扩能改造,给2台225t/h高压锅炉带来的除氧器热量过剩、锅炉给水温度升高、主蒸汽温度降低等一系列问题,分析了产生问题的原因,从节约能源、提高锅炉效率考虑,提出了相应的解决问题的办法:利用热量分流、改造省煤器管、增加二级过热器受热面积。经过3年多的生产实践证明,取得了良好的效果。     

RanGen: A Random Network Generator for Activity-on-the-Node Networks

In this paper, we describe RanGen, a random network generator for generating activity-on-the-node networks and accompanying data for different classes of project scheduling problems. The objective is to construct random networks which satisfy preset values of the parameters used to control the hardness of a problem instance. Both parameters which are related to the network topology and resource-related parameters are implemented. The network generator meets the shortcomings of former network generators since it employs a wide range of different parameters which have been shown to serve as possible predictors of the hardness of different project scheduling problems. Some of them have been implemented in former network generators while others have not.     

Drying Kinetics of a Porous Spherical Particle and the Inversion Temperature

A model is presented for drying of a single porous particle with superheated steam and humid air. Experimental data for spherical porous ceramic particle reported in the literature were used for the validation of the model. An inversion temperature at which the evaporation rates within superheated steam and humid air are equal was predicted. The effect of thermophysical properties of the particle (permeability 10^-14 - 10^-17 m², diameter 3 × 10^-3 - 10 × 10^-3 m) and operating variables (gas mass flux 0.26 - 0.78 kg m^-2 s^-1, drying agent temperature 120-200°C) is tested. The inversion temperature is shown to be affected by the thermophysical properties of the porous particle and of the drying agent.     

俄罗斯减速器涡轮钻具驱动PDC钻头在西西伯利亚油田的成功应用

涡轮钻具由前苏联研制出来以后，得到了迅速发展，目前已发展到减速器涡轮钻具阶段。现在，俄罗斯西西伯利亚地区普遍使用减速器涡轮钻具钻井，而减速器涡轮钻具驱动PDC钻头的使用还是空白。采用俄罗斯生产的几种不同型号的减速器涡轮钻具，在西西伯利亚进行了驱动PDC钻头钻井的阶段性试验。试验结果表明，在优选PDC钻头结构的情况下，用减速器涡轮钻具驱动PDC钻头，钻头进尺和机械钻速都较牙轮钻头有显著的提高，经济和社会效益显著。介绍了试验中使用的3种俄罗斯减速器涡轮钻具(TPM-195，TPⅢ-195和TPO3—195)的结构特点和主要技术参数。     

运用现代CFD方法设计高效率的汽轮机(续前期)

论述了运用现代计算流体动力学(ComputationalFluidDynamics,CFD)技术设计高效率汽轮机的方法,典型应用的实例有全三维叶片级流场、叶片汽封和排汽蜗壳计算。计算结果和实际是相符的。进一步对结构性单元和非结构单元程序的计算结果进行了比较,已证明,非结构单元CFD程序用于复杂形状的流场计算时,结果与实际相当一致,并具有独特的功能。     

宾馆酒店蒸汽冷凝水回收问题剖析

分析了宾馆酒店进行冷凝水回收所遇到的各种问题，提出了应对策略和解决方法，介绍了取得的应用效果。     

基于DSP+CPLD的高精度信号发生器

介绍了基于直接数字式频率合成(DDS)原理的全数字信号发生器(DSP),利用DSP芯片快速、高精度的运算优势以及CPLD芯片灵活的编程逻辑、大容量存储功能的特点,采用通用可编程芯片以及数字波形合成技术,形成高稳定、高精度、高动态的数字合成信号.该信号发生器可产生0～25 kHz的正弦波、三角波和方波,输出电压峰峰值为0～5 V,频率步进1 Hz,幅度步进0.001 V.     

Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.