CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Energy use in controlled temperature marine aquaculture

Temperature control offers benefits in land‐based marine aquaculture: stock growth rates may be enhanced by heating in winter; mortality rates in summer may be reduced by cooling. However, if the plant is not well designed, temperature control may create very large energy demands. This paper describes the application of temperature control in abalone aquaculture in New Zealand, with a focus on energy considerations in plant design. An abalone farm using a semi‐closed water conditioning system is used as a case study for which an energy model, based on a heat pump system, is developed. The model is used to determine the impact of plant design and tank conditions on the economics of the operation. Copyright © 2002 John Wiley & Sons, Ltd.     

NO emission characteristics in counterflow diffusion flame of blended fuel of H2/CO2/Ar

Flame structure and NO emission characteristics in counterflow diffusion flame of blended fuel of H₂/CO₂/Ar have been numerically simulated with detailed chemistry. The combination of H₂, CO₂ and Ar as fuel is selected to clearly display the contribution of hydrocarbon products to flame structure and NO emission characteristics due to the breakdown of CO₂. A radiative heat loss term is involved to correctly describe the flame dynamics especially at low strain rates. The detailed chemistry adopts the reaction mechanism of GRI 2.11, which consists of 49 species and 279 elementary reactions. All mechanisms including thermal, NO₂, N₂O and Fenimore are taken into account to separately evaluate the effects of CO₂ addition on NO emission characteristics. The increase of added CO₂ quantity causes flame temperature to fall since at high strain rates a diluent effect is prevailing and at low strain rates the breakdown of CO₂ produces relatively populous hydrocarbon products and thus the existence of hydrocarbon products inhibits chain branching. It is also found that the contribution of NO production by N₂O and NO₂ mechanisms are negligible and that thermal mechanism is concentrated on only the reaction zone. As strain rate and CO₂ quantity increase, NO production is remarkably augmented. Copyright © 2002 John Wiley & Sons, Ltd.     

几种高级便携式打印机性能特点比较

本文是对市场上几款高级便携式打印机主要性能特点的比较考察报告，包括：佳能生产的CanonBJC-70型便携式彩色喷墨打印机，惠普生产的HPDeskJet340型便携式彩色喷墨打印机和Pentax生产的Pentax PocketJet便携式打印机，后者必须使用热敏纸。     

Physico-chemical properties of ceramic pigments for high-temperature application

Heat resistant coatings are required primarily for stacks, exhaust pipes, reactors, space crafts and similar equipments that are permanently or occasionally exposed to elevated temperatures. High-temperature coatings are generally based on silicone resin with ceramic and metallic pigments. In this study, iron oxide, cobalt oxide (thermo chromic compound) and aluminum oxide are used for the preparation of four new types of coloured pigments. The thermal resistant characteristics of these ceramic pigments were studied by differential thermal analysis, thermo gravimetric analysis and differential scanning calorimetric analysis. These ceramic pigments are found to be thermally stable up to 400 °C.     

Synthesis and characterization of new thermally stable poly(ester‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic dihydroxy compounds

A series of new alternating aromatic poly(ester‐imide)s were prepared by the polycondensation of the preformed imide ring‐containing diacids, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A model compound (3) was also prepared by the reaction of 2b with phenol, its synthesis permitting an optimization of polymerization conditions. Poly(ester‐imides) were fully characterized by FTIR, UV‐vis and NMR spectroscopy. Both biphenylene‐ and binaphthylene‐based poly(ester‐imide)s exhibited excellent solubility in common organic solvents such as tetrahydrofuran, m‐cresol, pyridine and dichloromethane. However, binaphthylene‐based poly(ester‐imide)s were more soluble than those of biphenylene‐based polymers in highly polar organic solvents, including N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide and dimethyl sulfoxide. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 261 and 315 °C. Thermal behaviour of the polymers obtained was characterized by thermogravimetric analysis, and the 10 % weight loss temperatures of the poly(ester‐imide)s was in the range 449–491 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resultant poly(ester‐imide)s exhibited nearly an amorphous nature, except poly(ester‐imide)s derived from hydroquinone and 4,4′‐dihydroxybiphenyl. In general, polymers containing binaphthyl units showed higher thermal stability but lower crystallinity than polymers containing biphenyl units. Copyright © 2005 Society of Chemical Industry     

RanGen: A Random Network Generator for Activity-on-the-Node Networks

In this paper, we describe RanGen, a random network generator for generating activity-on-the-node networks and accompanying data for different classes of project scheduling problems. The objective is to construct random networks which satisfy preset values of the parameters used to control the hardness of a problem instance. Both parameters which are related to the network topology and resource-related parameters are implemented. The network generator meets the shortcomings of former network generators since it employs a wide range of different parameters which have been shown to serve as possible predictors of the hardness of different project scheduling problems. Some of them have been implemented in former network generators while others have not.