半浮动芯棒连轧荒管壁厚不均的原因分析

介绍了半浮动芯棒连轧管机荒管壁厚不均的类型及特点,荒管壁厚不均有同批壁厚不均、纵向壁厚不均和横向壁厚不均等3种类型。分析了荒管壁厚不均产生的原因,穿孔毛管壁厚不均、连轧管机孔型形状变化、轧制中心线偏移均会造成荒管横向壁厚不均;芯棒尺寸波动会引起荒管纵向壁厚不均和同批壁厚差。提出了改善半浮动芯棒连轧荒管壁厚不均的有效措施。     

铝—钢双金属复合轧制层厚比及轧制力的研究

用实验方法研究了铝－钢双金属复合轧制时层厚比的变化规律。给出了双金属复合时轧制力的计算式。     

火箭发动机包覆层测厚时间延迟估计算法研究

用超声测量火箭发动机包覆层厚度时,当包覆层较薄时检测回波信号会出现时域混叠。为此提出一种时间延迟估计的新方法。该方法能对修正的检测信号能量谱的对数微商求逆傅里叶变换。实验结果表明,该方法能准确估计出时域混叠信号的延迟时间。提高了火箭发动机包覆层厚度测量精度。     

Deformation behavior ofA6063 tube with initial thickness deviation in free hydraulic bulging

Experiment on seamless tubes of aluminum alloy A6063 with initial thickness deviation of 0-20% was conducted through a free hydraulic bulging with tube ends free. The influence of initial thickness deviation on the cross-section profile, thickness distribution, maximum internal pressure and maximum radial expansion was investigated. FEM simulation was also performed in order to examine and help explaining the experimental results. The results indicate that the internal pressure and maximum internal pressure appear to be little influenced by the initial thickness deviation, and that the cross-section profile of the bulged tube changes diversely and can not be a perfect circle. The results also suggest that the increase in initial thickness deviation may lead to a remarkable decrease in maximum radial expansion, and a rapid increase in thickness deviation and the center eccentricity of the inner and outer profiles.     

水压轴向柱塞泵配流盘最小水膜厚度的理论分析——结构参数的影响

最小水膜厚度是保证配流盘静压支承工作的基本条件，本文提出了最小水膜厚度应满足的基本要求，在两种不同的运动副表面粗糙度下，分别讨论了配流盘静压支承的主要结构参数对最小水膜厚度的影响，另一方面，分析结果又为结构参数的设计提供了参考依据。     

Diffusion bonding/superplastic forming of Ti-6Al-6V-2Sn/SUS 304 stainless steel/Ti-6Al-6V-2Sn

The superplasticity of the Ti- 6Al- 6V- 2Sn alloy for different temperatures was evaluated by single-sheet free blowing. The optimal superplastic temperature for the Ti- 6Al- 6V- 2Sn alloy was found to be 850 °C. Diffusion bonding of Ti- 6Al- 6V- 2Sn and 304 stainless steel was carried out in a vacuum. The interface of both bonded alloys was examined by EPMA. The concentration profile of Ni exhibited a peak at the interlayer and a valley adjacent it, whereas that of Cr exhibited a peak where Ni showed the valley. X- ray diffraction (XRD) analyses showed that the Fe ₂ Ti, NiTi, and CrMn Intermetallic compounds and the Cr element formed at the interface. The thickness profiles of the blown specimens were measured and compared with theoretical calculations.     

冷连轧机末机架AGC控制方式分析

介绍了冷连轧机末机架AGC控制3种方式的特点和适用范围，得出控制方式的选取须同时考虑轧制产品、轧机能力的发挥、板形、轧辊和后道工序的要求等多方面因素。     

一种智能纸张厚度计设计

根据纸张厚度测量控制系统的功能要求,应用β射线吸收原理,完成了一种智能纸张厚度计设计。它以MSP430FG479为微处理器,具有CAN和RS—485通信接口,具有自检测和自标定功能。给出了系统硬件实现方法,软件设计流程。经实验验证,检测精度达到0.1%以上。该设计方案,换用不同的放射源,可对各种纸和纸板的厚度进行检测,易于操作,工作稳定。     

电磁超声检测钢板厚度实验的参数优化

为提高电磁超声检测信号的信噪比,研究激励信号频率、脉宽及换能器提离距离对厚度测量结果的影响,搭建了电磁超声实验系统。该系统利用RITEC-SNAP 5000产生高能正弦波激励电磁超声换能器EMAT ( Electromagnetic Acoustic Trans-ducer),通过调节激励信号的频率、脉宽,改变提离距离来观测超声回波幅度的变化。实验结果表明：当激励频率和EMAT固有频率相同时其换能效率最高,采用6个周期的脉冲串时前后波包之间分界明显,为获得较大的回波幅度应尽可能减小提离距离。     

以临界屈曲应变为判断依据的非开挖内衬修复设计改进方法

《城镇排水管道非开挖修复更新工程技术规程》(CJJ/T 210-2014)选取管道的长期弹性模量EL进行内衬修复设计,并规定EL为短期弹性模量Es的0.5倍,但是对于这一做法的理论依据仍然存在较多质疑,也导致设计过于保守。据此考虑引入临界屈曲应变理论,提出以内衬的临界屈曲应变εr为破坏判据,并选取管道短期弹性模量Es进行设计的改进方法。研究表明,改进后的设计方法能够保证内衬设计在理论上的正确性,满足内衬的长期强度要求,减小大约21%的内衬设计壁厚,能够有效降低工程成本。