Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

有机介质中合成二硫化钛

本文研究了硫化氢与四氯化钛在某些有机介质中的反应，并提出了一个合成二硫化钛的新方法。该法是将干燥的硫化氢通入沸腾的四氯化铁的α－氯代萘溶液中，使硫化氢和四氯化钛发生复分解反应而生成二硫化钛。方法简便易行。Ｘ－射线物相鉴定及化学分析结果表明，产物为单一物相的、符合化学计量的二硫化钛。     

Ti 离子注入 LiNbO_3表面光学性能

本文研究了 x,y,z 三种切向的 LiNbO_3单晶片注入350keV 高能 Ti 离子(注入剂量为1.5×10~(17)/cm~2)后的表面光学性能。利用光谱仪及 AUEL 椭偏仪对三种切向 LiNbO_3试样在不同工艺处理后的光透射率及折射率进行了测试。注入损伤造成的光损耗可通过热处理消除,使晶格结构恢复至与完整晶格排列相近;注入层的折射率可增加11—13％左右。     

铵离子交换处理负硬水供锅炉应用技术

本文论述了负硬水只用氯化铵再生时离子交换器的运行过程及离子交换软化除碱的方法,并阐述了控制出水中残留碱的简便方法。经研究证明,此方法可达到除碱度、除硬度、除盐、延长锅炉使用寿命、减少腐蚀、减少排污量、节约燃煤等效果。经济效益十分显著。     

离子注入对铁及其低合金、铝及其合金耐腐蚀性能的影响

离子注入对金属腐蚀行为的研究已达30年．研究结果表明离子注入对改变金属表面成分和表面性能是极为有效的技术．本文概述了离子注入对铁及其低合金、铝及其合金的腐蚀电化学行为的影响．涉及的注入离子达十余种。     

氮离子注入尼龙1010的摩擦学特性

用高能离子注入机对尼龙 10 10进行 N+注入改性 ,注入能量为 4 5 0 ke V,剂量分别为 5× 10 14 /cm2 、2 .5× 10 15/cm2 及 1.2 5× 10 16/cm2 。以 Zr O2 及 Si3N4 球为上球样 ,分别与注入尼龙 10 10下盘样组成摩擦副 ,在销盘摩擦试验机上评价它们在干摩擦条件下的摩擦磨损行为。结果表明 ,几种剂量的 N+注入均增强了尼龙 10 10的耐磨性。未注入样品的磨损主要表现为粘着、塑性变形、犁沟和疲劳脱层 ,注入样品的磨损主要为轻微的磨粒磨损。     

等离子体浸没式离子注入-离子束增强沉积TiN膜研究

本文采用一种新型的等离子体浸没式离子注入 离子束增强沉积的技术(PIII IBAD),在Cr12MoV钢基体上制备出了TiN膜,对沉积膜的组织进行了光电子能谱分析,并对沉积膜进行了硬度检测、摩擦试验及磨痕形貌分析。试验结果表明,沉积膜中的组织为TiN、TiO2和Ti2O3,TiN膜具有高达Hv3200的高硬度和极其优良的摩擦性能。     

Effect of carbide additions on grain growth in TiC−Ni cermets

The growth of carbide particles in TiC-XC-2 vol.% Ni and TiC-XC-30 vol.% Ni alloys, where X=Zr, Cr, W, Ta and Mo, was fitted to an equation of the form d³-d_o ³=Kt. The grain growth behavior during liquid phase sintering at 1673K decreased markedly with the addition of Mo₂C or WC, changed little for TaC, and increased with the addition of ZrC or Cr₃C₂. The grain contiguity decreased with increasing Ni content in the TiC−Mo₂C−Ni alloy and was greater in the alloys with smaller growth rate constant. Consequently, the effect of carbide addition on the grain growth of 2 vol.% Ni alloys was found to be similar to that of 30 vol.% Ni alloys. The grain growth mechanism could be explained by the effect of contiguous carbide grain boundaries in restricting the overall grain growth, as well as the area of the solid/liquid interfaces in the alloy by the usual solution/reprecipitation model.     

酸溶性钛渣酸解工艺研究

针对攀枝花钛铁矿冶炼钛渣的物化性质，对影响钛渣酸解率和钛液指标的各个因素进行了全面系统的实验室研究，并在年产2000t钛白生产线上进行了工业验证和优化试验，酸解率稳定在93％以上，三价钛控制在1－3g/L，钛液浓度较钛矿酸解提高了40－50g/L，其它钛液指标达到了后续水解工艺的要求。