Microstructure and thermal cycling behavior of thermal barrier coating on near-α titanium alloy

Two kinds of thermal barrier coatings (TBCs), consisting of NiCoCrAlY bond coats (BCs) deposited by electron beam-physical vapor deposition (EB-PVD) and high velocity oxy-fuel (HVOF) thermal spraying, respectively, and top 8 wt%Y₂O₃–ZrO₂ (8YSZ) ceramic layers deposited by EB-PVD were prepared on near-α titanium alloys. The field emission scanning electronic microscopy and microhardness indentation are used to study the microstructure and microhardness. Different failure features including cracking patterns and the delamination degree of these two TBCs are discussed according to the thermal cycling tests in the atmosphere. It is found that the morphology of the two BCs deposited by different methods (EB-PVD and HVOF) determines the microstructure and microhardness of their corresponding top 8YSZ layers. The BC prepared by EB-PVD is dense and homogeneous, which leads to a dense and hard 8YSZ with clustered slim columnar grains. The BC prepared by HVOF, however, is porous and inhomogeneous in microstructure and, as a result, the top ceramic layer is loose with low microhardness and clustered coarse columnar grains.     

离子取代凝胶——ACA离子取代动力学模型

用动边界模型描述了海藻酸-壳聚糖-海藻酸(ACA)离子取代凝胶对2价离子的取代动力学过程.模型具有较好的可靠性，ACA离子取代凝胶对2价离子的取代属于颗粒扩散控制.ACA离子取代凝胶对Pb²⁺的反应级数是0.76.     

ECS-100 DCS控制系统在离子膜制碱装置中的应用

介绍某公司引进的离子膜制碱装置采用国产DCS系统的原由，系统的结构及特点。详细论述ECS-100 DCS在装置的特殊控制、顺序控制、联锁等方面的应用情况。     

过量TiO2助烧剂对Ba0.998La0.002TiO3陶瓷晶粒生长的影响

采用电性能测定和微观结构分析等方法研究了过量TiO2助烧剂对Ba0.998La0.002TiO3陶瓷晶粒生长的影响.结果表明:对于Ba0.998La0.002TiO3陶瓷在有液相参与烧结的晶粒溶解-淀析过程中,晶粒生长的必要条件是不仅要有液相的形成,而且BaTiO3晶粒必须在液相中有一定的溶解度.由于BaTiO3晶粒在Ba6Ti17O40和Ba2TiSi2O8液相中有足够的溶解度,促进了晶粒的生长,同时旌主掺杂离子进入晶格而释放氧,形成半导性的陶瓷,而BaTiO3晶粒不能溶解于Ba2Ti2SiP2O13液相中,抑制了晶粒的生长.     

含Fe~(3+)的酸液对钢铁的腐蚀作用及其抑制

钢铁制品的酸浸去除轧制铁鳞以及换热设备酸洗除锈除垢时有Fe~(3+)产生.通过恒电位法和失重法研究了含Fe~(3+)的酸液对钢铁的腐蚀作用及其抑制,结果表明:Fe~(3+)的存在会促进钢铁的腐蚀,一定结构的硫脲衍生物和阴离子表面活性剂之间存在协同效应,能有效地抑制氢离子放电的阴极过程和Fe~(3+)还原的阴极过程,从而抑制金属的腐蚀.     

扩散渗析法从钛白废酸中回收硫酸

针对钛白废酸的回收,在静态扩散条件下测定了硫酸、硫酸亚铁在阴离子交换膜中的渗析系数以考察膜的分离性能。进一步考察动态扩散操作参数如流量、流量比、停留时间等对回收率及回收酸浓度的影响。研究表明,使用的阴离子交换膜具有良好的分离性能,酸盐分离系数达23.6,在水酸流量比维持在1～1.1,废酸流量维持在0.6L·h-1左右的条件下,硫酸回收率大于85%,硫酸亚铁透过率小于7%。     

Effect of cation structure on the electrochemical and thermal properties of ion conductive polymers obtained from polymerizable ionic liquids

Several onium cations having vinyl group formed ionic liquids after coupling with bis(trifluoromethanesulfonyl)imide. These monomers were polymerized, and the relation between onium cation structure and properties of thus polymerized ionic liquids was investigated. The polymerized ionic liquid having ethylimiadzolium cation unit showed the highest ionic conductivity of around 10⁻⁴ S cm⁻¹ at 30 °C among the obtained polymers reflecting the lowest glass transition temperature of −59 °C. These polymers were thermally stable and their decomposition temperatures were about 350 °C. The ionic conductivity of the polymerized ionic liquids decreased by both the addition of lithium bis(trifluoromethanesulfonyl)imide and the polymerization in the presence of cross-linker. However, the polymerized ionic liquid having 1-methylpiperidinium cation structure showed good lithium ion transference number of 0.43 at room temperature.     

用钛白废酸和废铁屑制备聚合硫酸铁试验研究

利用钛白废酸和废铁屑制备了无机高分子絮凝剂聚合硫酸铁。详细研究了聚合硫酸铁制备过程中各因素对亚铁氧化、三价铁水解和聚合等过程的影响。确定了制备聚合硫酸铁的最佳工艺条件为：(1)氧化过程：pH为1．5，氧化剂与亚铁的物质的量之比为0．3，氧化温度为60℃，氧化时间为3h；(2)聚合过程：硫酸根与全铁的浓度比为1．4，陈化时间为2h。     

The Effect of Aluminum Ions on the DC Etching of Aluminum Foil

A study has been made of the electrochemical etching of 99.99% aluminum foils at a current density of 50 mA cm^–2in AlCl₃–HCl solutions (1 m Cl^–) at 80 °C. The solutions were made by dissolving metallic aluminum into 1m HCl solution, to give a Cl^– concentration of 1 m. The number density of etch tunnels and the homogeneity of tunnel length decreased, and the mean pit size and its standard deviation increased with increasing Al³⁺ concentration. The results were discussed based on potential transients at a current density of 50 mA cm^–2, current–potential curves at a scan rate of 10 m Vs^–1 and electrochemical impedance spectra.     

纳米二氧化钛制备方法研究

目前制备纳米二氧化钛粒子的方法很多,在总结归纳的基础上对各种制备方法所具有的特点进行比较,并指出了其优缺点和适用范围以及相关的研究进展.