Combined shape and sizing optimization of truss structures

 In this paper, an evolutionary optimization method is presented for weight minimum problem of a 3-dimensional truss structure in terms of nodal coordinates and element cross-sectional areas. The structure is subject to stress, local buckling and displacement constraints. Two types of design variables with different natures are optimized separately: (1) a fully stressed design (FSD) and scaling techniques are applied to sizing variables and (2) the evolutionary node shift method is applied to shape variables. Alternating procedure is utilized to couple the two types of variables and to combine the results. The optimum solution is achieved gradually from the initial configuration design. Two typical truss structures are examined to illustrate the validity of the method. Received: 22 October 2001 / Accepted: 04 June 2002 This research work is supported by the National Natural Science Foundation of China under the guarantees no. 10072050 and 10172072, respectively.     

堤身的数据采集及断面设计的几点建议

针对堤防设计的基础资料采集和设计优化，提出了一些合理性建议。     

Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²     

Paste Residence Time in a Spouted Bed Dryer. III: Effect of Paste Properties and Quality Interactions

The aim of this study was to evaluate the effects of paste properties on residence time during drying in a spouted bed dryer with inert bodies. The effect of paste solids content, surface tension, and viscosity on the residence time distribution and the mean residence times were studied using factorial experimental designs. The inert bodies used were glass and polyethylene beads. The mean residence times varied from 13.6 to 16.3 and 12.2 to 17.7 min for drying on glass and polyethylene beads, respectively. The analysis of variance showed that mean residence times significantly depended on solids content and surface tension for glass beads and also on viscosity for polyethylene beads. The residence time distributions for all conditions studied fitted well to the perfect mixing cell when applying the continuous stirred vessels in series model analysis. The powder density, flowability, and particle size depended on paste properties and inert type.     

Bridging process and structure through criteria

Scholars in design face two central challenges in design methods inquiry: firstly, to integrate process and solution, and secondly, to examine developmental junctures leading to innovation. With these goals in mind, we maintain that design criteria deserve greater attention and illustrate this position with a study of noted designers' use of criteria. The primary finding was that five criteria functions were considered during the design process. The study also explored potential relationships between designer variables (i.e., professional expertise and personality type) and criteria use.     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

《燃气红外线辐射供暖系统设计选用及施工安装》国家标准图集介绍

介绍了该国家标准图集的主要内容：设计说明、典型设计、工程实例、系统设备、燃气管道安装、液化石油气气化站、电气控制及温度检测、施工安装说明。     

Effects of temperature, ammonium and glucose concentrations on yeast growth in a model wine system

In enology, alcoholic fermentation is a complex process involving several mechanisms. Slow and incomplete alcoholic fermentation is a chronic problem for the wine industry and factors leading to sluggish and stuck fermentations have been extensively studied and reviewed. The most studied cause of sluggish and stuck fermentation is the nitrogen content limitation. Nevertheless, other factors, such as temperature of fermentation and sugar concentration can affect the growth of yeasts. In this study we modelled the yeast growth‐cycle in wine model system as a function of temperature, sugar and ammonium concentrations; the individual effects and the interaction of these factors were analysed by means of a quadratic response surface methodology. Cell concentrations and weight loss were monitored in the whole wine fermentation process. The results of central composite design show that lower is the availability of nitrogen, higher is the cell growth rate; moreover, initial nitrogen concentration also influences survival time of Saccharomyces cerevisiae.