静态电子轨道衡组成部分解析及其合理选择

阐述静态电子轨道衡诸多优点;工作原理、允许误差及误差分配;轨道衡的结构组成部分、解析各部分的工作特性及技术指标要求;合理选配及推荐实例.     

NUMERICAL ANALYSIS AND EXPERI- MENT OF UNSTEADY THERMAL FIELD OF ROTOR PLATE FOR EDDY CURRENT RETARDER

The physical model based on heat transfer theory and virtual boundary method for analyzing unsteady thermal field of rotor plate for eddy current retarder used in automobile is established and boundary conditions are also defined. The finite element governing equation is derived by Galerkin method. The time differential item is discrete based on Galerkin format that is stable at any condition. And a new style of varying time step method is used in iteration process. The thermal field on the rotor plate at the radial and axle directions is analyzed and varying temperature at appointed points on two side-surfaces is measured. The testing and analytical data are uniform approximately. Finite element method can be used for estimating thermal field of the rotor plate at initial design stage of eddy current retarder.     

Performance analysis of IEEE 802.11 ad hoc networks in the presence of exposed terminals

The paper evaluates the performance effects of exposed terminals in IEEE 802.11 ad hoc networks in finite load conditions. It derives analytical models for the estimation of channel utilization and media access delay for IEEE 802.11 ad hoc networks in finite load conditions with and without exposed terminals. The simulation results show that the analytical estimated channel utilization and media access delay metrics are fairly accurate.     

二次盐水及离子膜电解工序常见问题简析

介绍了二次盐水及离子膜电解工序的主要设备和流程,对二次盐水及离子膜电解工序运行中出现的问题进行了分析,并提出了解决措施。     

三相异步电动机运行指标的分析

利用电机学理论分析了影响电机起动转矩、起动电流、最大转矩和最小转矩的因素。     

Prediction of spectral reflectance factor distribution of automotive paint finishes

It is necessary to determine the accurate reflectance of painted surfaces for the review of paint finishes by computer graphics (CG) before actual painting of the exterior color of automobiles, and for quality control during production and inspection processes. We have optimized a method for measuring reflectance by using a statistical technique. We have found that the reflectance of a painted surface is best measured at an incident angle of 60° and at five aspecular angles of 10°, 18°, 28°, 40°, and 90°. Our method makes it possible to accurately reproduce reflection characteristics of paint finishes containing special flake pigments, such as pearl mica. Also it was proved that our method can apply not only to solid and metallic coatings but to all painted surfaces. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 275–282, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20125     

Copolymerization of bromophenylmaleimide with ethyl or butyl methacrylate

N‐p‐Bromophenylmaleimide (BrPMI) does not polymerize in solution by conventional free radical mechanism. However, it readily polymerized in bulk when mixed with a free radical initiator and heated in a microwave oven for 7–8 min. Copolymerization of ethyl methacrylate or butyl methacrylate with BrPMI was conducted in dioxane. The copolymers were characterized by IR and ¹H NMR spectroscopy and gel permeation chromatography. The monomer reactivity ratios were calculated by a non‐linear least‐square analysis. Thermal analysis indicated a great improvement in thermal stability of the copolymers compared with the methacrylate homopolymers. BrPMI was also polymerized in bulk in the DSC pan, which allowed the calculation of the activation energy of its polymerization. Copyright © 2003 Society of Chemical Industry     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.