纳秒级上升时间的高压脉冲群电源

按照IEC 61000-4-4/GB 17626.4—1998的要求，首先应用PSPICE仿真确定电路中各元件的参数值，然后基于拉普拉斯变换用MATLAB求解二阶电路验证各元件参数。在此基础上研制了一台以开关电源作为高压直流电源、以氢闸流管作为主控开关的脉冲群电源。该电源体积小、重量轻、效率高、成本低廉。试验结果表明，其输出信号符合标准要求，可用于快速瞬变脉冲群抗扰度试验。     

GPS在水面流速流向测量中的应用

传统的水面流速流向测量多采用经纬仪交会法,此法需要大量的人力和设备,工作量大且费时。近几年,随着全球定位系统(GPS)的广泛应用和实践,在一定范围内,采用GPS定位法替代经纬仪交会法施测水面流速流向。介绍了GPS定位法的测量原理、设备,以及测量方法。通过对GPS定位法的精度和优缺点的分析,得出采用GPS定位法施测水面流速流向具有较高的推广价值。     

Iodide mediated electrolysis of acidic coke/coal suspension

Hydrogen is among the emerging energy vectors that are being developed to replace nonrenewable hydrocarbon energy sources. The preferred method to produce hydrogen without generating greenhouse gases is the electrolysis of water using renewable energy. The reduction of energy during the water electrolysis process is a desirable goal regardless of the source of electric power. Similar to ferrous/ferric mediation, iodide can be used as a mediator in the electrolysis of an acidic suspension of coke or coal. The iodide ion is oxidized at a far lower anodic potential than the alternative oxygen evolution reaction. This reduces the cell electrolysis voltage and, consequently, reduces electricity use. The iodide consumed at the anode is continuously regenerated by chemical reaction with the coke/coal in suspension.     

14 kV single-phase superconducting fault current limiter based on YBCO films

We present the fabrication and short circuit test results of a 14 kV single-phase resistive superconducting fault current limiter (SFCL) based on YBa₂Cu₃O₇ (YBCO) films. Individual components were processed using the 4″ YBCO films and have the rated voltage and current of 600 V and 35 A at 77 K, respectively. Twenty four components, eight components in series and three lines in parallel, make a module having the rated voltage and current of 4.8 kV and 105 A, respectively. Three modules were assembled in series to produce the SFCL working at 77 K, a 14 kV single-phase machine for the 22.9 kV Y-Y grid. short circuit tests were successfully conducted in an accredited test facility with the maximum fault currents up to 14.1 kA_P. All components quenched together upon faults and shared the rated voltage evenly without any supplementary device between the modules. This proves that the SFCL based on YBCO films may not only work reliably at 22.9 kV, but also provide technical feasibility for higher voltage application including the transmission grids.     

Study of Liquid Phase Shifter for ICRF on EAST

A method of current drive with Ion Cyclotron Range of Frequency （ICRF） on Experimental Advanced Superconducting Tokomak （EAST） is described. A variety of liquid silicon oil heights in the phase shifter will bring the phase difference to the current drive. It is found that the current drive can be achieved by using the phase shifter. The liquid phase shifter is one of the impedance matching systems too.     

Influence of deposition parameters on hole mobility in polymorphous silicon

Time-of-flight transient photoconductivity measurements reveal a monotonic increase with the deposition pressure in the hole mobility in polymorphous silicon for samples deposited under hydrogen dilution. With helium dilution, a maximum mobility that matches the highest value from H-dilution samples is measured at the intermediate pressure of 1.4 Torr. The deposition rate of those samples is twice the rate for the H-dilution ones. For the samples with the best hole mobilities, the valence-band tail is comparable to the one of standard hydrogenated amorphous silicon.     

KEIO/72000/0.003型电抗器替代进口设计

本文通过分析电炉电极间短路电流，确定电抗器主要技术参数及设计依据。     

桥丝电阻分布的均匀性对发火电流的影响

文中分析了桥丝电阻分布的均匀性对电雷管发火电流的影响，并对试验结果作了分析和讨论。     

PFC控制技术的一种改进方案

文章首先指出了目前ＰＦＣ所用控制技术的缺陷，然后提出了一各改进方案，并从理论分析和仿真验证的角度证明了改进方案的可行性和先进性。     

Optimisation of metallic pigments in coatings by an electrochemical technique and an investigation of manganese powder as pigment for metal rich primers

Zinc dust and manganese powder as pigments were incorporated in epoxy-polyamide and butyl titanate medium, with different pigment volume concentration (PVC) ranging from 20 to 74. These protective coatings were coated on sand blasted mild steel substrates and immersed in 3 wt.% sodium chloride solution and the corrosion current was measured by the Tafel extrapolation method. From the corrosion current produced by these primers, the optimum level of the pigments in these binders was identified. Thus the protective performance of optimised primers was evaluated on a sand blasted mild steel surface by the Tafel polarisation method in 3 wt.% sodium chloride solution, over different periods of time. The results were found to be comparable with the salt spray test and galvanic current measurements. The manganese powder used for this investigation showed that it could be used as an alternative to zinc powder for metal rich primers.