85W／90卡车手动变速箱油的研制

介绍８５Ｗ／９０卡车手动变速箱油的组分和添加剂，提出符合８５Ｗ／９０粘度级别的基础油，讨论影响８５Ｗ／９０卡车手动变速箱油性能的各种因素，给出符合８５Ｗ／９０卡车手动变速箱油规格的油品配方。     

节理岩体参数对围岩破损区影响的敏感性分析

本文针对黄河拉西瓦地下水电站工程，对节理岩体诸参数对围岩破损区范围的影响进行了敏感性分析。指出了主要敏感参数，对这些参数影响围岩破损区的趋势和可能程度进行了讨论，并对勘察和施工提出了一些意见。     

强度调制／直接检测（IM／DD）光纤通信系统色散限制的研究

通过引入归一化脉宽Ｐ和相对脉冲展宽因子ｑ，提出了一个适用于ＩＭ／ＤＤ系统中各种眼图恶化量ｘ和归一化脉宽Ｐ的色散限制改进公式。通过与其它理论的比较、计算机仿真和对实验数据的分析，验证了该公式的正确性，并给出了其它结果的限制条件。研究表明：当眼图恶化量ｘ为１ｄＢ左右时，对２．５Ｇｂ／；外调制信号（α＝０）而言，非色散位移光纤ＩＭ／ＤＤ系统的色散因子γ约等于０．７９，所对应的系统再生中继距离约为９００余公里。     

搅拌工艺对半固态Y112铝合金组织及性能的影响

采用自行研制的机械搅拌装置,研究了不同工艺参数对半固态Y112铝合金组织及性能的影响.研究表明,搅拌温度越高,搅拌速度越大,固相颗粒越细小、均匀和圆整,其抗拉强度与伸长率越高;但温度太高,固相颗粒会熔化,抗拉强度及伸长率也降低;随搅拌时间的延长,固相颗粒先变得细小、均匀和圆整,然后长大,抗拉强度、伸长率先升高后降低.     

Numerical study on PEMFC’s geometrical parameters under different humidifying conditions

Steady-state and three-dimensional simulations were carried out to study the influences of geometrical parameters on the performance of PEMFC under different hydrating conditions. Flow fields, species transport, transport of water in polymer membrane and movement of liquid water in cathode and anode porous layers were determined, in order to accomplish a complete estimation of ohmic and concentration losses of PEMFC power. The geometrical parameters were thickness of the polymer membrane, cathode catalyst layer as well as gas channel to rib width ratio. Every simulation was made under different relative humidities of inlet flows (50 and 100%) for every change of characteristic length. Results show that the influence of the geometrical parameters on ohmic and concentration losses is of considerable importance. The performance of PEMFC is seriously affected under dehydrating conditions. However, such performance may be considerably improved by using suitable geometrical parameters. Cathode and anode liquid saturation may not only affect the transport of species, but also the polymer electrolyte water content. These results show the importance of simultaneously calculating both the water absorption and desorption through the polymer electrolyte and the liquid saturation in the cathode and anode porous mediums to obtain an actual view of ohmic and concentration losses of the PEMFC performance.     

一种考虑不同期合闸的行波合闸保护新方法

当线路末端故障时，行波在线路末端的反射情况比较复杂，反向电流行波的极性有可能与正向电流行波的极性相反，而此时测距结果又与线路无故障时相同。因此，会造成行波测距式与行波极性比较式合闸保护的不正确动作。根据行波的折、反射理论，分析出当线路无故障时正向电流行波仅在线路末端发生反射，且电流行波的反射系数为-1，而当线路存在故障时，正向电流行波将在故障点发生反射，无论故障是否在线路末端，电流行波的反射系数都不会是-1。根据这一特征，提出了一种新的行波合闸保护方法。从原理上保证了在各种情况下保护都可以正确动作，大量的电磁暂态仿真结果也证明了这一点。     

单稳态触发器的结构及其开关级设计原理

根据单稳态触发器定时单元特性,提出了单稳态触发器的一般结构.在此基础上,运用传输电压开关理论进行了CMOS单稳态触发器的开关级设计研究,并具体设计了两个单稳态触发器.设计实例表明文中提出的方法不仅简单、有效,而且具有通用性.     

Lattice Distortion Analysis Directly from High Resolution Transmission Electron Microscopy Images—the LADIA Program Package

Direct strain mapping from high resolution transmission electron microscopy images is possible for coherent structures.At proper imaging conditions the intensity peaks in the image have a constant spatial relationship with the projected atom columns.This allows the determination of the geometry of the projected unit cell without comparison with image simulations.The fast procedure is particularly suited for the analysis of large areas.The software package LADIA is written in the PV-WAVE code and provides all necessary tools for image processing and analysis.Image iintensity peaks are determined by a cross-correlation technique,which avoids problems from noise in the low spatial frequency renage.The lower limit of strain that can be detected at a sampling rate of 44 pixels/nm is ≈2%.     

光波分复用技术及其应用

分析了波分复用系统的组成原理和几种分类方式,最后给出了一些基本应用形式。     

谐振式力传感器敏感结构的研究

利用材料力学及弹性力学法，对石英晶体谐振式力传感器的悬臂梁结构进行了研究，得出了双梁单岛及三梁单岛悬臂梁结构的力转移系数，在与实验结果进行了比较后证明，支承结构的理论推导与实验结果一致。