钛容器的特点

根据钛材的化学、物理、力学和工艺性能介绍了钛容器在设计、制造、检验和应用方面的特点。     

焊接波浪状边缘薄钢带的高上山成型法

介绍了高上山成型法的工艺特点及理论上的可行性和实践中的可靠性，此方法能有效地解决薄钢带波浪状边缘的焊接方面存在的问题。     

海底沉积物中天然气水合物生成和分解规律研究进展

对国内外有关海底沉积物中天然气水合物生成和分解规律方面的研究进行了详细调研,得到如下结论:天然气水合物的生成和分解条件在海底沉积物中与在井筒、管道中有明显不同,其主要原因是多孔介质中流体与孔隙壁面间的界面效应对海底沉积物中天然气水合物的形成条件会产生明显影响;在海底沉积物中天然气水合物生成和分解条件的数值模拟技术研究方面,研究者大都假设以天然气水合物作为盖层的成藏类型,借助常规油气藏数值模拟技术进行模拟研究;影响海底沉积物中天然气水合物生成和分解条件的因素很多,因此海底沉积物中天然气水合物生成和分解规律研究必须借助试验模拟、数值模拟和现场测试相结合的综合方式进行。该调研成果可为今后天然气水合物经济有效开采技术方案选择和进行天然气水合物危害控制等提供参考。     

利津地区深层沙三、沙四段油藏测试评价

利用测试资料，将利津地区深层沙三、沙四段油藏分为5种油藏类型：①高压、低-极低渗、导数曲线后期上翘、地层存在非均质性的油藏；②高压、低渗、无污染、双孔介质的油藏；③高压、低-中渗、无-轻微污染的复合油藏；④常-高压、低渗、有污染的油藏；⑤常-高压、极低渗、无污染、干层的油藏。最后对利津地区深层沙三、沙四段各种类型油藏进行了评价，认为利津地区深层沙三、沙四段自然产能较低，一般需要进行改造措施来提高渗透性，提高产能。     

浸入凝胶法聚合物膜形成机理的研究现状

从热力学、传质动力学、相分离机制和固化过程几方面综述了浸入凝胶过程中聚合物膜形成机理的研究现状 .指出浸入凝胶成膜过程是传质交换和由传质交换引发的相分离以及其后的固化过程之间相互竞争的复杂非平衡过程 ,膜结构是上述几个过程竞争的结果     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

省煤器管开裂原因分析

对省煤器开裂管进行了化学成分及宏、微观分析。分析结果表明，在高温高压条件下，在其焊缝溶合区出现粗大的魏氏组织，管材中的珠光体组织产生了不同程度的球化，而母材组织又存在严重的带状组织。在过热条件下熔合区极易出现裂纹，并由此快速扩展，造成省煤器管开裂。     

Micro-RBS characterisation of the chemical composition and particulate deposition on pulsed laser deposited Si1−xGex thin films

The formation and deposition of particulates by pulsed laser deposition of Si_1−xGe_x semiconductor alloy thin films are discussed. Using Rutherford backscattering spectrometry with micrometer lateral resolution (micro-RBS) the film composition was measured with high accuracy, even in the presence of particulates with a high areal density of 20,000–30,000 particulates per mm². We show that on impact of a particulate, the part of the thin film which is already deposited probably melts and its Ge content segregates to the surface.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

海洋平台双相不锈钢管线的焊接

就双相不锈钢的特异性能．介绍双相不锈钢管线的焊接特点与技术。