 基于混合模型的优化低频低压减载方法研究

文中以低频低压情况下保证电压稳定的前提下减载为研究内容,提出了一种基于混合模型的优化低频低压减载方法。该混合模型将遗传算法与人工神经网络相结合,在保证电压稳定的情况下选择合适的节点进行负荷切除。实验结果表明,该方法可以在低频低压情况下使负荷减载量达到最小。     

微电网跟踪调度计划双层双时间尺度实时控制策略

为了提升微电网跟踪调度计划的能力,并降低分布式电源和负荷的功率波动对跟踪效果的影响,提出一种利用由超级电容和电池储能组成的混合储能系统跟踪调度计划的双层双时间尺度实时控制策略。上层基于模型预测控制方法建立日内滚动优化模型,结合分布式电源和负荷的超短期功率预测结果,综合考虑一段时域内的跟踪偏差及混合储能系统的功率和荷电状态对跟踪调度计划进行滚动优化;下层在上层优化结果的基础上,采用基于荷电状态的混合储能系统实时控制策略对超级电容和电池储能的实时功率进行协调分配,进一步降低分布式电源和负荷的实时功率波动对跟踪效果的影响。通过仿真算例对所提控制策略进行验证,结果表明:所提策略不但实现了良好的实时跟踪调度计划的控制效果,而且优化了超级电容和电池储能的荷电状态。     

Processing of yttria partially stabilized zirconia thermal barrier coatings implementing a high-power laser diode

Several studies have been undertaken recently to adapt yttria partially stabilized zirconia (YPSZ) thermal barrier coating (TBC) characteristics during their manufacturing process. Thermal spraying implementing laser irradiation appears to be a possibility for modifying the coating morphology. This study aims to present the results of in situ (i.e., simultaneous treatment) and a posteriori (i.e., post-treatment) laser treatments implementing a high-power laser diode. In both cases, the coatings underwent atmospheric plasma spraying (APS). Laser irradiation was achieved using a 3 kW, average-power laser diode exhibiting an 848 nm wavelength. Experiments were performed to reach two goals. First, laser post-treatments aimed at building a map of the laser-processing parameter effects on the coating microstructure to estimate the laser-processing parameters, which seem to be suited to the change into in situ coating remelting. Second, in situ coating remelting aimed at quantifying the involved phenomena. In that case, the coating was treated layer by layer as it was manufactured. The input energy effect was studied by varying the scanning velocity (i.e., between 35 and 60 m/min), and consequently the irradiation time (i.e., between 1.8 and 3.1 ms, respectively). Experiments showed that coating thermal conductivity was lowered by more than 20% and that coating resistance to isothermal shocks was increased very significantly.     

聚氨酯-聚丙烯酸酯复合乳液的动态力学性能

采用种子乳液聚合法合成了聚氨酯一聚丙烯酸乙（丁）酯[PU／PE（B）A]复合乳液。并研究了不同组成对复合乳液性质、相客性、阻尼性能及拉伸性能的影响。耐水性及稳定性测试表明，随PE（B）A含量的增加，涂膜的耐水性变好，而乳液的稳定性变差。动态力学性能测试（DMS）表明，合成的PU／PE（B）A复合乳液为半相容体系，其相容性随PE（B）A含量的增加而增强。DMS和拉伸试验表明PU／PEA／P（B）A（质量比50／25／25）复合乳液具有优良的阻尼性能、抗拉强度和断裂伸长率，可用作宽温域阻尼涂料。     

Hydrogen sorption sites in the gallium containing hybrid catalysts used for the aromatization of light alkanes

Gallium species which were incorporated initially in the oxide form, were all in the (+3) oxidation state in the hybrid catalyst and exhibited two types of hydrogen chemisorption sites, s_hw and s_hs. The stronger sorption sites shs which predominated at higher gallium dispersion, corresponded probably to the most effective surface configuration for gallium in the aromatization ofn-butane.     

壳聚糖/磷钙杂化膜的制备与性能研究

将壳聚糖/钙盐复合膜浸泡在磷酸二氢钾溶液中制备了壳聚糖/磷钙杂化膜.用电子扫描电镜观察杂化膜和膜内磷钙微粒的形貌,研究了杂化膜的力学性能、溶胀率、吸光度及热稳定性.结果表明,杂化膜内磷钙晶体为柱状和层状结构,磷钙被包裹在杂化膜内,并与壳聚糖膜形成紧密的连续结构.随着膜中磷钙的质量分数从2.1%增加到8.0%,膜的溶胀率从102%增加到144%,其在200～800 nm波长范围的吸光度也逐渐增加.当磷钙的质量分数为7.0%时,杂化膜的力学性能最佳,其拉伸强度为54.42 MPa、弹性模量为4045.72 MPa、断裂伸长率为4.85%.杂化膜的热分解温度为299℃,高于壳聚糖膜的分解温度290℃.这种具有层状磷钙结构的杂化膜具有良好的生物相容性,可作为一种潜在的支架材料.     

聚酰亚胺/二氧化硅杂化膜的制备与介电性能的研究

采用溶胶-凝胶法制备了BTDA-ODA聚酰亚胺/SiO2杂化膜,利用红外分光光度计（FTIR）、热重分析仪（TGA）和透射电镜（TEM）研究了杂化膜的微观结构和热性能,并对杂化膜的介电常数（e）和介电损耗（tand）随SiO2粒子含量和电场频率的变化进行了分析和讨论。结果表明：杂化膜的介电常数和介电损耗随SiO2粒子含量的增加而增大,随电场频率的升高而逐渐降低,用考虑到粒子的形状因素和两相间相互作用的EMT模型可以预测聚酰亚胺/SiO2杂化膜的介电常数。     

一体化复合式膜生物反应器除磷研究

本文通过对比实验，研究了不同工艺组合条件下一体化复合式膜生物反应器（HCMBR）的除磷效果，研究表明，在无厌氧段的情况下，反应器内保持好氧状态的同时，填料内部存在厌氧环境，TP的去除率为22％，在有厌氧段（A／O）的情况下，TP的去除率可达70％，采用化学方法时，TP去除率可达82．1％，但过高的n(Al^3 )/n(TP)值将会影响污泥的活性，并且HCMBR对NH3－N，CODCr,TN等污染物有十分良好的去除效果。     

NCO含量对聚氨酯-丙烯酸酯复合乳液性能的影响

以甲苯二异氰酸酯(TDI-80)、聚醚二元醇(N210)、二羟甲基丙酸(DMPA)和甲基丙烯酸甲酯(MMA)为主要原料，采用原位乳液聚合法，合成聚氨酯-丙烯酸酯(PUA)复合乳液。在保证DMPA含量、中和度等不变的情况下，研究了NCO／OH物质的量之比对乳液的性能及外观的影响。