屏边岔河电站机组缺陷分析及处理

1电站概况屏边岔河电站属径流引水式电站,总装机2×7·5MW,额定水头190m,额定流量4·67m3/s,水轮机型号HLB54—WJ—113,发电机型号SFW7500—8/2150,额定转速750r/min。机组布置形式为三支点,两段轴。机组油系统采用外油循环,油经下位油箱齿轮泵加压通过油冷却器打到上位重力油箱,由上位重力油箱再自流到3道轴承进行润滑、冷却。2机组暴露的缺陷及处理方案2·1设计上的缺陷2·1·1现象电站于2004年1月投产。刚投产试车时,2台机水导轴承上的瓦温均有同样现象:负荷带到5MW时,推力瓦温较正常,为45℃。水导瓦温度则很快上升到62℃,负荷往上…     

提高冷冲压模具寿命的措施

本文分析了冷冲压模具失效的基本形式及原因，从多方面探讨了提高冷冲模寿命的措施。     

Thermal—Mechanical Fatigue Behavior and Life Analysis of Cast Ni—base Superalloy K417

In-phase(IP) and out-of-phase(OP)thermal-mechanical fatigue(TMF) behavior of cast Ni-base superalloy K417 was studied.All experiments were carried out under total strain control with temperature cycling between 400-850℃.Both in-phase and out-of-phase TMF specimens exhibited cyclic hardening followed by cyclic softening at the minimum temperature.Besides,they cyclically hardened in the early stage of life followed by cyclic softening at the minimum temperature.Besides,they cyclically hardened in the early stage of life followed by cyclic softening at the maximum temperature.OP TMF life was longer than of IP TMF.Various damage mechanisms operating in different controlled strain ranges and phasing were discussed.A few life prediction methods for isothermal fatigue were used to handle TMF fatigue and their applicability to superalloy K417 was evaluated.The SEM analysis of the fracture surface showed that transgranular fracture was the principal cracking mode for both IP and OP TMF.Oxidation was the main damage mechanism in causing shorter fatigue life for IP TMF compared with OP TMF.     

大幅度延长电池寿命的智能传感系统

采用MSP430F123快闪微控制器、ADS7822和TPS60311的系统方案     

注硼中子寿命测井技术在华北油田的应用与发展

注硼中子寿命测井技术是近几年发展起来的一项用于测量开发井水淹状况 ,分析层间油水关系 ,根据其结果采取合理措施降水增油的新技术。该技术在华北油田推广应用以来 ,取得了较好的效果。在应用过程中 ,不断优化选井原则 ,优选注硼参数和测注工艺 ,突出综合对比解释 ,进一步提高了工艺技术应用的合理性、准确性以及解释结果的吻合性 ,一定程度上丰富了注硼中子寿命测井理论 ,促进了该项技术的完善与提高     

基于价值工程的机械产品设计模式初探

介绍了价值工程的基本理论，对机械设计过程中引入价值工程理论的方法进行了研究，提出运用此理论的意义和应遵循的准则，并对运用的具体方法进行了初步探讨。     

注硼中子寿命测井注硼工艺优化设计

注硼中子寿命测井是一项水淹层测井新技术 ,对老油田的产层分析评价、剩余油含量估算等方面发挥了重要的作用。但测井施工时 ,往往由于注硼工艺不当导致硼酸的渗吸量难以准确反映地层可动水的含量 ,从而产生解释上的困难和误区。在渗流与扩散理论相结合的基础上 ,结合华北油田的施工实践 ,介绍了确定注硼管柱、硼酸用量、注硼压力以及硼酸扩散时间的基本原则和实际经验 ,为工艺的优化设计提供了一些方法与思路