基于FPGA的TDM over IP的设计

设计一种TDM over IP的技术系统。该系统用FPGA将E1数据包通过串并转换到千兆以太网数据包,经IP网传输到终端设备,再通过并串转换将以太网数据包转换成E1数据包完成传输。经过软件和硬件测试验证了此系统在千兆以太网上传输的可行性,系统没有出现误码,固有输出抖动是0.55UI,最大峰值抖动指标均满足ITU-G.823标准要求。     

奥氏体化温度及冷却方式对20Mn2SiVB钢组织及性能的影响

通过各种试验手段,研究了20Mn2SiVB钢不同奥氏体化温度及不同冷却方式处理后其显微组织及其强度和塑性的变化,确定了最佳的热处理工艺。结果表明:900℃奥氏体化后风冷时钢的强塑性最好;在强塑性最佳时的微观组织是铁素体+粒状贝氏体。     

大剂量Si-Mn复合孕育剂在铸铁中的应用

从例证和机理两方面来说明通过大剂量Si Mn复合孕育在铸铁中的应用 ,使Mn的作用得到充分发挥 ;Mn13是提高铸铁组织中珠光体量和性能的理想元素 ;通过调节大剂量Si Mn复合孕育剂中Mn的比例来稳定和提高基体组织中的珠光体量 ,达到稳定和提高铸铁性能的目的 ,它的可操作性比通过控制化学成分来稳定和提高铸铁的性能更好更容易 ,冲天炉熔炼效果更明显。     

Intermetallic phase formation in directionally solidified Al−Si−Fe alloy

The present study has been undertaken to better understand the solidification behavior of Al−Si−Fe alloys containing 7wt.% Si and 0.9wt.% Fe, with particular regard to the formation of phase during controlled solidification and influence of growth rates on intermetallic phase selection. The alloys studied were Al-7Si-0.9Fe alloys, which were produced by a modified Bridgman solidification arrangement. These alloys were solidified unidirectionally with different growth rates (1–30mm/min). The solidified microstructure of these alloys consists of the growth of primary aluminum and multiple second phase reactions.     

TYPHOON PROCESS AND ITS IMPACT ON THE SURFACE CIRCULATION IN THE NORTHERN SOUTH CHINA SEA

A severe typhoon Utor,occurring between July 3 and 8,2001,brought heavy rainfall,strong wind and storm surge.Utor was responsible for tremendous destruction and economic losses in Philippines,Taiwan and Guangdong.An air-sea model system (MM5 and Princeton Ocean Model(POM))was built to simulate meteorological dynamics and ocean circulation in the South China Sea(SCS).In the POM the output of MM5 was used as the input data.With an increased number of vertical levels,a high-resolution planetary boundary layer scheme and updated landuse/vegetation data,the accuracy of computing wind,temperature and other meteorological fields are improved in near surface and upper levels in MM5 simulations.The simulated trajectory and wind speed of Utor are close to the observed results.The simulated distribution of rainfall is accorded well with measured data in the Pearl River Delta(PRD)area.At different meteorological stations in Hong Kong,the wind,temperature and sea surface pressure are well simulated.The simulated ocean surface current and surface temperature fields have an obvious rightward-biased response to the typhoon Utor,and the maximum velocity and the lowest temperature region appear in the 30 km of the right side of the typhoon track.The typhoon Utor could make the water 50m under the surface ocean unwell to surface and the ocean surface temperature decrease by about 2°C.     

一种消除阶梯效应的图像分解新模型

针对TV-L1分解模型在进行图像分解时所得到的结构部分有阶梯效应的问题,本文提出一种改进的图像分解模型即GJTV-L1模型。该模型首先得到结构部分的切向量场,由切向量场可得到结构部分的法向量场,然后拟合法向量场得到重构图像,即结构部分。通过仿真实验,验证了GJTV-L1模型和算法的合理性及有效性。     

Direct 5-axis tool-path generation from point cloud input using 3D biarc fitting

In reverse engineering, geometrical information of a product is obtained directly from a physical shape by a digitizing device. To fabricate the product, manufacturing information (usually tool-path) must be generated from a CAD model. The data digitized must be processed and in most cases, a surface model is constructed from them using some of the surface fitting technologies. However, these technologies are usually complicated and the process for constructing a surface patch from a massive digitizing data is time-consuming. To simplify the process for getting tool-path information, a simple algorithm is proposed in this paper. The algorithm is used to generate a 5-axis machining tool-path. Instead of implementing any complicated surface fitting techniques, a direct method is proposed for constructing three-dimensional (3D) triangular mesh from the digitizing data with the mesh points considered as the tool contact locations. Depending on the locations of the points digitized, a decimation procedure is applied such that some of the digitizing data will be filtered out. Then, the tool axis orientations which must be determined in 5-axis tool-path are calculated and the tool center locations are determined accordingly. A 3D biarc fitting technique is applied for all the tool center locations so that a complete 5-axis tool-path is obtained.     

MD5碰撞攻击中的充要条件集

通过分析MD5中非线性函数的性质以及模2³²减差分和异或差分的性质,证明了Liang Jie和Lai Xuejia 给出的产生MD5碰撞的充分条件集中的条件是保证第23～62步的差分路径满足的充要条件,给出了保证第63、64步的输出差分满足的充要条件集.利用得到的充要条件集,提出了对MD5的改进的碰撞攻击算法,该算法的平均计算复杂度约为已有碰撞攻击算法的0.718 7倍,并通过实验对该算法的改进效果进行了验证.     

无线混合网络配电监控系统设计

介绍了无线混合网络配电监控系统的设计,通信部分采用基于不同无线网络技术的CDMA1X和WLAN。给出了系统软硬件结构的设计模式,最后讨论了在配电监控系统中使用无线网络通信的关键技术。