Adaptive control of siso plants with unmodelled dynamics

In this paper we pursue a twofold aim. First we want to simplify the complexity of the classical Monopoli's scheme, the so-called ‘Augmented error signal control scheme’. Then we also wish to cope with the realistic situation in which the presence of unmodelled dynamics has to be taken into account. This latter problem has been faced in the literature by suitably modifying the adaptation mechanism in order to avoid undesired phenomena as well as to obtain an attractive stability region for the state trajectories starting from any point in a predefined initial condition set. In our case the necessity of introducing any sort of modification in the adaptation mechanism is completely avoided, but we still obtain asymptotic stability of the output error signal.     

用不稳定试井资料研究油藏储集层流动系统模式：以准东油区为例

从不稳定试井Ｈｏｒｎｅｒ曲线形态分类入手，结合油藏动态特征对油藏储集层流动系统进行分类，并初步确定出各类流动系统的特征参数及其相应的开采特点。根据不稳定试井Ｈｏｒｎｅｒ曲线形态，可以把相应的储集层流动系统划分为三大类（孔隙流动系统、双重介质流动系统、裂缝流动系统）五个亚类。特别提出了双重介质孔缝串并流动系统组合模式。这无论对新区开发方案的编制，还是老区开发政策的制定都具有重要的借鉴参考价值。     

The formalization and analysis of a communications protocol

The MSMIE protocol [SBC89] allows processors in a distributed system to communicate via shared memory. It was designed to meet the reliability and efficiency needs of applications such as nuclear safety systems. We present a formal model of the MSMIE protocol expressed in the notation CCS. Desirable properties of the protocol are expressed in the modal mu-calculus, an expressive modal logic. We show that the protocol lacks an important liveness property. In actual operation, additional operating constraints are checked to avoid potential problems. We present a modified protocol and show that it possesses the liveness property even without checking operating constraints. We also show how parts of the analysis were automated with the Concurrency Workbench.     

相似理论在真空灭弧室研究和设计中的应用

本文应用相似理论得出,真空灭弧室中电弧运动速度与电流强度成线性关系的相似准则,和极限开断电流与触头直径、开距间的经验公式。认为用小电流模型来研究大电流真空灭弧室是可行的。     

齿轮减速器造型设计与模态分析

讨论复杂结构的建模方法,建立齿轮减速器三维实体模型并进一步建立了齿轮减速器的三维有限元模型,分析系统的固有特性,从而获得了设计所需的必要数据。     

Putting it all together – Formal verification of the VAMP

In the verified architecture microprocessor (VAMP) project we have designed, functionally verified, and synthesized a processor with full DLX instruction set, delayed branch, Tomasulo scheduler, maskable nested precise interrupts, pipelined fully IEEE compatible dual precision floating point unit with variable latency, and separate instruction and data caches. The verification has been carried out in the theorem proving system PVS. The processor has been implemented on a Xilinx FPGA. A shorter version of this article with the title “Instantiating uninterpreted functional units and memory system: functional verification of the VAMP” appeared in [8]. The work reported here was done while all the authors were with Saarland University.     

Study on axiomatic rules for building up relationships between requirement and source programs

The purpose of our study is to build up relationships between requirement and source programs with our originally thought-out rules. When other rules to be derived from these original rules are applied to software development, even a single instruction in a programming language could be determined, and the program would satisfy the requirement. More specifically speaking, these rules will turn into a formula or a prototype of software programs. Hence, when the variables in the requirement are placed in the formula, we can get a required program in an automatic way.     

水浴法加温液氧泵

1　故障现象一次 ,我们用KL -1 5型制氧制氮车开机制氮 ,给一只容积为 40升、最高工作压力为1 4 7MPa的气瓶灌充氮气 ,当气瓶充气压力升高到一定值时不再上升。反复开泵 ,压力基本不变。液氧泵停止时 ,出口压力无明显下降。经分析判断导致气瓶压力升高到一定值时不再上升的原因是由于液氧泵被冻结所致。2　排除方法首先关闭液氧泵。拧开制冷机氢气放气阀 ,使压力下降到 1 0MPa。开大放气阀 ,使二级压力保持在 0 3 5MPa左右。调整正流空气调节阀 ,调节好中部温度。关闭液氮进液氧泵阀和气氮出液氧泵阀。戴棉布手套 ,拆开液氮进口接头、…     

SBR工艺发展应用综述

关于SBR工艺的书籍和文章很多。本文在这些资料的基础上整理总结 ,对经典SBR工艺的应用进行了综述 ,归纳了经典SBR工艺的特点 ,介绍了各种新型SBR工艺。     

Delamination Analysis for Laminated Composites. II: Numerical Verification

A validation of the delamination analysis models developed in a companion paper is provided through comparisons of predictions with finite‐element and elasticity solutions. The models are applied to the analysis of composite compression specimens reinforced with end tabs. An elasticity solution for the gage section of the specimens is developed. A comparison of the characteristic roots shows that the predictions of the models include the material and geometric parameters that control the behavior, and the roots corresponding to the basic stretching and bending modes are accurately predicted. The stress distribution at the interface between tabs and specimen is in good agreement with a finite‐element simulation. The interlaminar shear and peel stresses show an exponential increase with a maximum intensity at the free edges of the tabs. The behavior of previously tested specimens is explained; and practical guidelines for specimen design are provided to avoid unwanted extraneous modes of failure. The influence of the deformation modes associated with each model is investigated. An assessment of the accuracy and level of complexity is presented.