贵金属Pd-P系非晶态合金研究进展

本文首先论述了含磷的钯基非晶态合金的物理和化学制备方法，并简要地介绍了Pd—P合金的各种物理化学性能，以及该类非晶态合金特殊用途。     

Effect of styrene–isopren–styrene addition on the recycled polycarbonate/acrylonitrile–butadiene–styrene polymer blends

Interfacial agents as compatibilizers have recently been introduced into polymer blends to improve microstructure and mechanical properties of thermoplastics. In this way, it is possible to prepare a mixture of polymeric materials that can have superior mechanical properties over a wide temperature range. In this study, an incompatible blend of Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) Copolymer were made compatible by addition of 5, 10, and 20% Styrene–Isopren–Styrene Copolymer (SIS). The mixing operation was conducted using a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by SEM and DSC techniques. Furthermore, the elastic modulus, tensile and yield strengths, percentage elongation, hardness, melt flow index, Izod impact resistance, heat deflection temperature (HDT), Vicat softening point values of polymer alloys of various ratios were determined. It was found that addition of SIS to the structures decreased the tensile strength, yield strength, elastic modulus, and hardness, whereas it increased Izod impact strength and percentage elongation values. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 559–566, 2006     

Electrochemical Behaviour of Al, Al—In and Al–Ga–In Alloys in Chloride Solutions Containing Zinc Ions

The electrochemical behaviour of Al, Al—In and Al–Ga–In alloys in 0.6 m NaCl solutions with and without Zn²⁺ was investigated. The study was performed by means of open circuit potential, potentiodynamic polarization, potentiostatic current-time and electrochemical impedance spectroscopy measurements as well as by SEM-EDAX examination. It was found that the Al—In alloy exhibits the highest negative open circuit potential in 0.6 m NaCl and the corrosion resistance of the tested electrodes decreases in the following order: Al > Al–Ga–In > Al—In. The greater activity of the Al—In alloy was interpreted on the basis of the autocatalytic attack by indium. The potentiostatic current–time measurements in Zn²⁺ containing electrolyte at potentials above the pitting potential revealed that Zn²⁺ has an insignificant influence on the Al electrode, while it enhances the corrosion of the Al–Ga–In alloy and improves the attack morphology of the Al—In alloy. Furthermore, the impedance spectra recorded under open circuit conditions showed a decrease in the polarization resistance of Al—In and Al–Ga–In alloys in presence of Zn²⁺ indicating the activating effect of Zn²⁺ ions.     

Structure and properties of polyimide‐bonded magnets processed from prepolymers based on diacetyl derivatives of aromatic diamines and dianhydrides

We report a novel method of polyimide (PI) synthesis from prepolymers based on dianhydrides and diacetyl derivatives of aromatic diamines that facilitate the preparation of a melt processable mixture at 300 ± 10°C of the prepolymer and magnetic Nd‐Fe‐B alloy to provide PI‐bonded magnets with enhanced properties. It is shown that chemical structure of the prepolymers strongly influences viscosity behavior via crystallization of the oligoimide in the melt, leading to formation of PI with rigid‐rod like structure. This structural ordering of the prepolymers based on diacetyl derivative of diamine used in this study, if not controlled, leads to exponential increase of melt viscosity with time, making it practically impossible to prepare melt processable mixture of the magnetic particles and the PI prepolymers at elevated temperatures. The results obtained demonstrate that appropriate dianhydrides and diacetyl derivatives of diamines that do not lead to crystallization of oligoimides in prepolymer mixture can be used under controlled processing conditions to prepare melt‐processable PI‐bonded magnets containing rigid‐rod like PI structure that significantly increases thermal stability of the magnets. The temperature dependencies of the magnetic properties of the PI‐bonded magnets under conditions that they are likely to encounter during their service life were found to be remarkably similar to that of commercial thermoplastic magnets such as injection‐molded nylon magnets. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 478–485, 2006     

Influence of polymerization conditions on the structure and properties of polyethylene/polypropylene in‐reactor alloy synthesized in the gas phase with a spherical Ziegler–Natta catalyst

A spherical TiCl₄/MgCl₂‐based catalyst was used in the synthesis of in‐reactor polyethylene/polypropylene alloys by polyethylene homopolymerization and subsequent homopolymerization of propylene in the gas phase. Different conditions in the ethylene homopolymerization stage, such as monomer pressure and polymerization temperature, were investigated, and their influences on the structure and properties of in‐reactor alloys were studied. Raising the polymerization temperature is the most effective way of speeding up polymerization and regulating the ethylene content of polyethylene (PE)/polypropylene (PP) alloys, but it will cause a greater increase in the PE‐b‐PP block copolymer fraction (named fraction D) than in the fraction of PP‐block‐PE in which the PP segments have low or medium isotacticity (named fraction A). Although changing ethylene monomer pressure could influence the ethylene content of PE/PP alloys slightly, it is an effective way of regulating the structural distribution. Reducing the monomer pressure will evidently increase fractions A and D. The mechanical properties of the alloys, including impact strength and flexural modulus, can be regulated in a broad range with changes in polymerization conditions. These properties are highly dependent on the amount, distribution, and chain structure of fractions A and D. The impact strength is affected by both fraction A and fraction D in a complicated way, whereas the flexural modulus is mainly determined by the amount of fraction A. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2136–2143, 2006     

Electrochemical behaviour of heat-treated AlZnMg alloys in chloride solutions containing sulphate

The electrochemical corrosion and passivation of Al5Zn1.7Mg0.23Cu0.053Nb alloys, submitted to different heat treatments (cold-rolled, annealed, quenched and aged, and quenched in two steps and aged), in sulphate-containing chloride solutions, has been studied by means of cyclic polarization, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), and X-ray photoelectron spectroscopy (XPS). The cyclic polarization curves showed that sulphate addition to the chloride solution produced a poor reproducible shift of the breakdown potential to more positive potentials. The repassivation potentials, much more reproducible, and practically separating the passive from the pitting potential region, were slightly displaced in the negative direction with that addition. When the alloys were potentiodynamically polarized in the passive potential region, sulphate was incorporated in the oxide film, thus precluding chloride ingress. In addition, Zn depletion was favoured, whereas Mg losses were avoided. Different equivalent circuits corresponding to different alloys and potentials in the passive and pitting regions were employed to account for the electrochemical processes taking place in each condition. This work shows that sulphate makes these alloys more sensitive to corrosion, increasing the fracture properties of the surface layer and favouring the pitting attack over greater areas than chloride alone.     

Deformation behavior and microstructure of an Al-Zn-Mg-Cu-Zr alloy during hot deformation

The hot deformation behavior and microstructures of Al-7055 commercial alloy were investigated by axisymmetric hot compression at temperatures ranging from 300°C to 450°C and strain rates from 10-2 to 10 s-1,respectively.Microstructures of deformed 7055 alloy were investigated by transmission electron microscopy (TEM).The dependence of peak stress on deformation temperature and strain rate can be expressed by the hyperbolic-sine type equation.The hot deformation activation energy of the alloy is 146 kJ/mol....     

Microscopic characterization of semi-solid aluminium alloys

The microstructural evolution and element distribution of the Al-4Cu-Mg alloy during semi-solid compression were investigated,and the precipitate behavior and dislocation morphology were discussed.The experimental results show that the microstructure,the number of CuAl2(θ phase) precipitates,and the dislocation density of the Al-4Cu-Mg alloy depend apparently on the process parameters.More segregation of Cu at the grain boundary happens with an increase of deformation temperature and a decrease of strain ra...     

Microstructural characterization of as-cast and homogenized 2D70 aluminum alloy

The microstructure of the as-cast 2D70 aluminum alloy and its evolution during homogenization were investigated by means of optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and differential scanning calorimetry (DSC) analysis. The results indicate that the microstructure of the as-cast 2D70 aluminum alloy mainly consists of the dendritic network of aluminum solid solution and intermetallic compounds (Al2CuMg, Al2Cu, Al9FeNi, Cu2FeAl7...