Al_(10)Zn_(2.9)Mg_(1.7)Cu超高强铝合金的喷射成形制备研究

采用喷射成形技术制备了Al1 0 Zn2 .9Mg1 .7Cu高强高韧铝合金沉积坯件 ,研究了喷射成形制备过程中各工艺参数对沉积坯件的成形性、显微组织、致密度的影响 ,确定了适当的工艺参数 ,研究了沉积坯件的热挤压及热处理工艺 ,对材料的组织进行了分析并对不同状态的材料性能进行了比较。研究结果表明 :当喷射成形工艺参数合理时 ,沉积坯件具有良好的成形性与致密度 ,在随后的热挤压过程中 ,通过较低的挤压比即可使材料达到全致密 ;通过对合金进行适当的热处理 ,材料的极限抗拉强度达到 810MPa ,同时延伸率保持在 8%～ 11% ,该材料是一种理想的轻质高强结构材料。     

Exchange and oxidation of CO on O-predosed Rh---Al2O3 and Rh---CeO2 catalysts

Exchange and oxidation of C¹⁶O were investigated at 450°C on ¹⁸O-predosed Rh and Pt catalysts supported on A1₂O₃, CeO₂ and CeO₂-Al₂O₃. In all cases, a rapid exchange of C¹⁶O with the surface can be observed. CO oxidation leads to C¹⁶O₂, C¹⁶O¹⁸O and C¹⁸O₂. Significant formation of C¹⁶O₂ is due to the relatively high ¹⁶O coverage in reaction resulting from the C¹⁶O exchange and from an exchange between O surface species and ¹⁶O internal atoms. Hydrogen is also formed via a water-gas shift reaction (CO + surface OH) in higher proportion on CeO₂-containing catalysts than on A1₂O₃. Chlorine inhibits all the reactions (exchange, oxidation and WGS) and particularly the internal exchange.     

硼／铝复合材料管构件的界面特性EI

主要研究带钛合金连接头硼／铝复合材料管构件中Ｂ－Ａｌ－Ｔｉ间的界面结构与性质。研究表明，在复合工艺条件下，硼－铝界面附近没有检测到任何铝－硼化合物，而钛－铝间形成ＴｉＡｌ有序金属间化合物相。实验证明，硼／铝复合材料与铝合金端环之间采用的固结方法是有效的，且可按照受载类型随意调整斜面搭接长度，达到承受不同载荷的目的。     

助剂对Pd/树脂醚化催化剂催化性能的影响 Ⅰ.铝助剂的影响

研究了不同助剂对Ｐｄ／树脂醚化催化剂在临氢条件下对催化裂化汽油Ｃ５馏份与甲醇和Ｈ２反应的催化性能的影响。结果表明，在Ｐｄ／树脂醚化催化剂中引入Ｚｒ、Ｔｉ、Ｂ、Ｓｎ和Ａｌ等助剂后，都能改善催化剂的醚化、双键异构和二烯烃选择性加氢活性，其中以Ａｌ、Ｓｎ为最好。Ａｌ助剂的体积质量和负载方式对Ｐｄ－Ａｌ／树脂醚化催化剂的活性有影响。ＢＥＴ方法和Ｘ－射线荧光光谱分析（ＸＦＳＡ）表明，Ａｌ助剂对Ｐｄ－Ａｌ／树脂醚化催化剂的表面积、孔结构和Ｐｄ离子交换量影响较小。     

连铸铝镇静钢的钢水准备

在连铸生产铝镇静钢时,水口絮流一直是困扰工程技术人员的一个难题.从絮流的原因入手,分析了Al2O3生成的控制.并介绍了几种钢水钙化的方法,从中比较出用复合造渣材料来解决浇铸铝镇静钢的优点.     

乙炔在磁稳定床中的选择性加氢研究

 制备了一种磁性Pd/Al₂O₃催化剂，采用磁稳定床考察了活性组分负载量、反应条件及CO浓度对乙炔加氢反应性能的影响。结果表明，当反应温度80℃、反应压力1.5MPa、空速9000h－1、磁场强度（H）25kA/m时，乙炔转化率为100％，乙烯选择性可达81％，具有优良的乙炔加氢活性和乙烯选择性，优于相同反应条件下的进口催化剂；250h稳定性实验结果表明，磁性Pd/Al2O3催化剂具有良好的初活性和乙烯选择性，催化剂性能稳定。     

棕刚玉粉中Al2O3含量分析方法的探讨

对耐火材料——棕刚玉粉的质量分析控制，提出了用实用性的检测方法测定其Al2O3含量。通过与国家标准分析方法的对比试验，证实快速实用分析方法测定棕刚玉粉中Al2O3含量是可行的。     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Characterization of two-phase nickel aluminides produced by pressure-assisted combustion synthesis

Two-phase (B2+L1₂) nickel aluminide intermetallic compounds were synthesized by the pressure-assisted volume combustion synthesis (CS). The production and characterization of the samples containing NiAl+Ni₃Al were investigated. Aluminum (99% pure, 15 μm) and carbonyl nickel (99.8 pure, 4-7 μm) powders were used. The production of intermetallic compound was carried out at 1050 °C under 150 MPa uniaxial pressure in open air atmosphere in an electrical resistance furnace for 60 min. The formation temperature of intermetallic compound was determined by differential scanning calorimeter (DSC) analysis, and exothermic temperature of powder mixture was determined as 653 °C. The characterization of samples was confirmed by optical microscope, SEM and XRD analysis. It was observed that the structure of compound has very low porosity and the formation of NiAl was completed successfully. The relative density of test materials measured according to Archimedes’ principle was 98.04%. The microhardness of test materials was about 351 HVN₁.     

深部调剖驱油交联剂的研究

为提高非均质性严重的地层原油采出率 ,合成了用于聚合物驱油的 4种交联剂 ,并对聚合物种类、用量和其与交联剂组成的体系进行了评价。 4 0℃下铝交联剂凝胶粘度低 ,酚醛树脂交联剂低温下不成胶 ,而有机铬交联剂 (J2 )和有机复合胺 (J3)交联效果好。当选用HPAM/有机铬交联剂 /有机酸交联体系时 ,其中HPAM相对分子质量为 2 1× 10 7,可通过改变体系pH值调节成胶速度 ,pH值 6 5时 ,14 0 0mg/LHPAM和 4 0 0mg/LJ2组成的体系在 4 0℃、30d可形成粘度为12 0mPa·s以上的凝胶 ,且热稳定性好 ,成胶时间能满足现场施工需要。 14 0 0mg/LHPAM和10 0 0mg/LJ3交联剂组成的体系 ,成胶时间长 ,有利于油田深部调剖驱油