Strengthening technology and mechanism for semi-solid die casting of aluminum alloy

Combined with theoretical evaluation,an optimized strengthening process for the semi-solid die castings of A356 aluminum alloy was obtained by studying the mechanical properties of castings solution treated and aged under different conditions in detail,then,the semi-solid die castings and liquid die castings were heat treated with the optimized process.The results show that the mechanical properties of semi-solid die castings of aluminum alloy are superior to those of the liquid die castings,especially the strengthening degree of heat treated semi-solid die castingsis much greater than that of liquid die castings with the tensile strength more than 330 MPa and the elongation more than 10％,and this is mainly contributed to the non-dendritic and more compact microstructure of semi-solid die castings.The strengthening mechanism of heat treatment for the semi-solid die castings of A356 aluminum alloy is due to the dispersive precipitation of the second phase(Mg2 Si) and formation of GP Zone.     

PC/ABS合金研究进展

概述了PC/ABS合金国内外的开发应用现状,并综述了国内外近年来对PC/ABS合金的研究进展,其中包括:PC/ABS合金的相容性技术、相容剂的选用及影响合金性能的因素:原料、组分的配比、成型条件等,并对该合金的发展方向作了简要的分析,认为PC/ABS合金的开发研究在国内塑料合金的工业开发、应用中极其重要,开发的核心是相容化技术。     

低熔点合金填充聚合物材料断口形貌研究

研究了合金元素、加工温度、金属含量、第三组分对低熔点金属填充聚合物材料断口形貌的影响。实验结果表明:不同的合金对体系的影响很大,低分子量、低结晶性聚合物,高的成型加工温度可提高材料的相容性。     

Computation of concentrations of characteristic atoms of alloys in BCC structure

In this paper,taking Nb-Mo alloy system as an example,the equations of concentration of characteristic atoms of alloys in BCC structure were obtained on the basis of the idea of systematic science of alloys and the number of coordination atoms.The concentrations of characteristic atoms in B2-NbMo type ordered alloys were calculated as functions of ordering degree(s) and composition xMo.When s=smax,the concentrations of characteristic atoms of stoichiometric B2-NbMo intermetallic compound are equal to that o...     

铝合金中锌、铁的快速测定--原子吸收分光光度法

样品以盐酸溶解，加入过氧化氢助溶，蒸至近干．加入1 1盐酸提取，移入100mL容量瓶中，分取部分溶液于50mL容量瓶中，调整盐酸酸度为5％，用水稀至刻度，摇匀后，以空气-乙炔火焰水相直接测定锌和铁。为了消除大量基体元素的影响，在标准系列中加入相当量的铝。此方法快捷、简便，亦可用于锰、镁、铜、铅、镍的测定。     

钯－银合金膜分离氢气的研究

采用厚为５０μｍ的Ｐｄ／Ａｇ（２３）合金膜进行了氢气渗透系数的测定和Ｈ＿２／Ｎ＿２混和气分离的研究，得出温度、压力、膜厚、进料气流量、膜的预处理和再活化及膜表面中毒等因素对氢气渗透的影响。分离Ｈ＿２／Ｎ＿２混和气可获得高纯氢气。     

CJ91胶粘剂在螺旋振动光整机中的应用

螺旋振动光整机槽内壁的橡皮保护层由于老化及磨损等原因出现裂口甚至脱落现象，严重影响设备的使用寿命和闸把壳体的外观质量。通过分析和试验筛选出螺旋振动光整机的理想胶粘荆——CJ91胶粘剂并介绍了粘接修补工艺。     

Cu-Zn-Al形状记忆合金直接淬火和分级淬火后马氏体稳定性的研究SCIEI

用透射电镜,X射线衍射仪和电阻法研究了Cu-14.84wt-％Zn-7.75wt-％Al形状记忆合金在直接淬火和分级淬火后马氏体的稳定性。试验结果表明,直接淬火和分级淬火(150℃,2min)后于室温时效约3h的马氏体均为M18R结构,但刚直接淬火后马氏体并不稳定,其某些衍射峰位置和电阻率均随室温时效而变化;而分级淬火(150℃,2min)后马氏体是稳定的,其所有衍射峰位置和电阻率几乎不随室温时效而变化。上述结果可用“马氏体再有序化机制”解释。     

Influence of Atomizing Gases on the Oxide-Film Morphology and Thickness of Aluminum Powders

Fine powders of aluminum were produced in a pilot-plant, inert-gas atomizerwith a confined-design nozzle, which operated vertically upward. Argonand helium at 1.85 MPa and nitrogen at 1.56 MPa were used as the atomizingagent. The morphology of the powder particles was examined by SEM. Powderswere sieved dry and wet. The Sauter mean diameter of the powders varied from20.70 to 10.25 m depending on the atomizing gas. The distribution ofsizes was bimodal. The mean thickness of oxide on the surface of the powderwas calculated from the total oxygen contents of powder samples (determinedby a Leco analyzer). In addition, ESCA measurements and BET tests werecarried out for surface-oxide thickness and area measurements,respectively. The finest powder produced under helium incorporated thinnersurface-oxide layers than the coarser ones produced under argon andnitrogen. This was due to differences in physical properties (such asdensity, thermal conductivity) and flow properties (such as gasvelocity and relative velocity) of the atomizing gases used, i.e., helium,argon, and nitrogen. The oxide was very irregular in thickness in thecoarse-size range of the Al powders produced under argon and nitrogen. Thiswas presumably because of the high- and low-temperature oxidation ofaluminum droplets during the atomization and subsequent solidification andcooling periods leading to the rough surfaces observed with SEMinvestigation in the present work.