F离子掺杂TiO2的性能研究

以NH4F为掺杂剂，采用溶胶-凝胶法制备F离子掺杂型TiO2光催化剂，对其进行XRD、XPS和PL表征，结果表明，F离子掺杂ToO2由于Ti—F配位体的形成而能抑制金红石相的生成，同时F离子掺杂能增加TiO2表面缺陷浓度并降低Ti2P键的结合能，另外，由于F离子能取代Ti—OH配位体而降低了表面羟基氧浓度．光催化研究结果表明，F离子掺杂提高了TiO2光催化活性近1．5倍．     

环氧树脂/蒙脱土纳米复合材料性能的研究

用一种新型的热稳定性较好的改性剂2，2’-二[4-(4-氨基苯氧基)苯基]-丙烷(BAPP)改性钠基蒙脱土，再与环氧树脂进行纳米复合制备了环氧树脂／蒙脱土纳米复合材料。讨论了蒙脱土用量对环氧树脂／蒙脱土纳米复合材料性能的影响，并对其结构和性能进行了表征和测试。结果表明：改性使蒙脱土层间距变大，制备出的环氧树脂／蒙脱土纳米复合材料剥离结构较好，环氧树脂／蒙脱土纳米复合材料的玻璃化转变温度和动态储能模量随改性蒙脱土用量的增加呈现较好的递增趋势。     

4-氨基吡啶的合成技术进展及其应用

评述了4-氨基吡啶的合成研究进展,重点介绍了硝基氮氧化吡啶法工艺。概括介绍了4-氨基吡啶在医药、农药、染料等领域的应用状况以及在国内外的生产现状。指出4-氨基吡啶合成工艺的难点在于降低生产成本,提高反应收率以及减少环境污染。建议从催化加氢还原或电化学还原过程中找到一条合乎国情的工艺路线,以推动我国吡啶系列产品的研发工作。     

Synergistic Influence of Poly(4-Vinylpyridine) and Potassium Iodide on Inhibition of Corrosion of Mild Steel in 1M HCl

The corrosion and inhibition behavior of mild steel in 1 M HCl in the presence of poly(4-vinylpyridine)(P4VP) and potassium iodide (KI) was investigated using weight loss measurements, potentiodynamic polarization studies and impedance measurements. The inhibition efficiency increased with increasing P4VP concentration. The inhibiting action of P4VP is considerably enhanced by the addition of potassium iodide. The adsorption of this compound either alone or in combination with iodide ions on the metal surface is found to obey Lamgmir's adsorption isotherm. The experimental results suggest that the presence of iodide ions in the solution increases the surface coverage and, therefore, indicate the joint adsorption of P4VP and iodide ions. On the other hand, it was found that the inhibiting effect of P4VP and (P4VP + KI) increased with increasing temperature of the corrosion medium. The presence of these species in the solution decreases the double layer capacitance and increases the charge transfer resistance, both derived from Nyquist plots obtained from a.c. impedance studies. The variation of charge transfer resistance with time suggests that the inhibitive action of (P4VP + KI) depends mainly on the protective inhibitor film formed on the steel surface.     

Adsorption and desorption characteristics of 2-methyl-4-chlorophenoxyacetic acid onto activated carbon

Adsorption and desorption characteristics of the 2-methyl-4-chlorophenoxyacetic acid (MCPA) from aqueous solution onto the activated carbon (GAC, F-400) were studied. Adsorption equilibrium capacities of the MCPA increased with decreasing pH and temperature of the solution. Adsorption equilibrium of the MCPA could be represented by the Sips equation. The internal diffusion coefficients were determined by comparing the experimental concentration decay curves with those predicted from surface diffusion model and pore diffusion model. The adsorption model based on the linear driving force approximation (LDFA) was used for simulating the adsorption behavior of the MCPA in a fixed bed. Over ninety five percent desorption of the MCPA could be obtained using distilled water.     

浅谈C语言中循环结构的教学--回答好循环结构的“三个问题”

循环结构是C语言程序设计中的重难点,其掌握情况对于后续章节的学习效果尤为关键。本文以什么是循环、何时需要使用循环以及如何使用循环三个问题为主线,通过精心选择的教学案例和灵活有效的教学方法来进行解答,以激发学生兴趣,培养编程思想。     

Scrolls and nested tubes in multiwall carbon nanotubes

Recent high-resolution transmission electron microscopy (HREM) studies of multiwalled carbon nanotubes (MWCNTs) reveal a class of defects analogous to edge dislocations in a crystal. These defects are believed to mark the transition from scrolls on one side to nested tubes on the other. On the tube side, layer spacing becomes irregular. Analysis of the helicity of the tubes shows a strong correlation between diameter and helicity. This suggests that the organizing principle for the tubes is not Van der Waals forces, as in the case of graphite or turbostratic carbon, but preservation of helicity. Based on these observations and total energy calculations, the authors speculate that graphene monolayers initially form scrolls and subsequently transform into multiwall nanotubes through the progression of defects. Scrolls and nested tubes thus coexist within a single MWNT.     

Evolution of chemistry and morphology during the carbonization and combustion of rice husk

Both fine carbon/silica and pure silica powders can be obtained by carbonization and combustion of rice husk under non-isothermal conditions, and the products can be used for preparation of high-quality ceramic materials. Studies on the morphology, chemical and physical characteristics of products were carried out by N₂-adsorptionmeter, SEM, XRD, FTIR, ICP-MS and EA. Results indicate that decreasing the heating rate increased the specific surface area, pore volume and pore diameter. At a heating rate of 5 °C/min, the specific surface areas of both the carbon/silica and pure silica powders were 261 and 235 m²/g, and the average pore diameters were 2.2 and 5.4 nm, respectively. The products obtained from various heating rates were all amorphous. Thermogravimetric analysis was employed to study the reaction characteristics during carbonization or combustion, indicating that decomposition process of rice husk could be divided into three temperature zones. This results of the study can also provide the important information on the recovery of biomass material from rice husk.