中原油田深井大井眼段钻井液工艺

濮深8井是中原油田在西部洼陷南部寻找接替储量的一口重点深探井,也是中原油田第一口井深达6000m的超深井。分析了濮深8井钻井液的配备及维护和处理技术,得出深井大井眼段钻井液工艺技术存在以下问题:井眼大,钻井液量及钻屑量多,处理时间长,处理剂用量多,处理频繁;返速低使钻井液清洗井眼的能力减弱;井下温度高使处理剂的作用明显降低,二氧化碳的侵入使钻井液性能变差。钻井液维护处理的较好方法是定时、定量补充处理剂胶液。固相控制是深井大井眼段钻井液工艺中的关键问题,必须配套并且有效地使用固控设备,以维护好钻井液性能。     

华北油田鄚东地区深井钻井液技术

鄚东地区钻井过程中经常发生垮塌、卡钻、井漏等复杂事故。该地区深井钻井采用了抑制性及封堵性较强的铵基沥青树脂高密度钻井液体系,并根据地层特点,对不同井段制定了相应的钻井液维护处理措施。结果表明,该钻井液体系抑制性好,抗温、抗污染能力强,性能稳定,成功地控制了复杂事故的发生,满足了该地区深层钻井的要求。     

用迁移率和载流子浓度研究碲镉汞中的深能级

获得了一种研究碲镉汞深能级的方法。通过分析迁移率 载子浓度与温度的关系，可以得到关于深能级的重要依据。     

Deep levels,electrical and optical characteristics in SnTe-Doped GaSb Schottky Diodes

The GaSb layers investigated were grown directly on GaAs substrates by molecular beam epitaxy (MBE) using SnTe source as the n-type dopant. By using admittance spectroscopy, a dominant deep level with the activation energy of 0.23-0.26 eV was observed and its concentration was affected by the Sb₄/Ga flux ratio in the MBE growth. A lowest deep-level concentration together with a highest mobility was obtained for GaSb grown at 550°C under a Sb₄/Ga beam equivalent pressure (BEP) ratio around 7, which should correspond to the lowest ratio to maintain a Sb-stabilized surface reconstruction. In the Hall measurement, an analysis of the temperature-dependent mobility shows that the ionized impurity concentration increases proportionally with the sample’s donor concentration, suggesting that the ionized impurity was introduced by an SnTe source. In addition, optical properties of an undoped p-, a lightly and heavily SnTe-doped GaSb layers were studied by comparing their photoluminescence spectra at 4.5K.     

升深2-17井络合铝聚合物充气钻井液现场试验

为加快徐加固子深层天然气的勘探开发步伐，缩短深层气井的建井周期，在升深2-17井进行了充气钻井试验。介绍了络合铝聚合物充气钻井液技术的现场应用概况及效果以及井漏的发生与处理过程、钻井液起泡的解决措施。在现场试验过程中，络合铝聚合物钻井液性能稳定，具有较强的抑制性和较好的流变性能，流性指数控制在0．7左右，具有良好的携屑和稳定井壁能力，而且粘度较低，基本上控制在33～52s之间，满足了现场充气和脱气的需要；该钻井液抗温可达180℃，润滑性能较好，在钻井过程中无粘卡显示，在深井欠平衡井眼稳定方面取得了较好的效果；在不同的气液比条件下，可以在0．83～1．08g／cm。之间实现对当量密度的调节;与常规钻井工艺相比，充气钻井可以使机械钻速提高30％～50％；在钻进过程中实现了充气和点火同时进行，达到了欠平衡钻井工艺技术的要求，为进一步开展气体钻井打下了良好的基础。     

大变量逻辑函数最佳覆盖问题研究

逻辑函数的最佳覆盖，一直是逻辑综合领域的关键环节。尤其是大变量逻辑函数最佳覆盖，对复杂的逻辑综合更为重要，但也更加困难。本文在对逻辑覆盖算法研究的基础上，提出了适合大变量逻辑函数最佳覆盖的Beister改进算法。经过大量算题的测试表明，改进的列覆盖算法在时间复杂度和选择效果方面均优于Beister算法。     

Controlled oxygen incorporation in indium gallium arsenide and indium phosphide grown by metalorganic vapor phase epitaxy

The defect engineering in metalorganic vapor phase epitaxy In_xGa_1-xAs and InP by controlled oxygen doping using diethyl aluminum ethoxide (DEALO) was developed in this study. DEALO doping has led to the incorporation of Al and O, and the compensation of shallow Si donors in In_xGa_1−xAs: Si with 0 ≤ x ≤ 0.25. With the same DEALO mole fraction during growth, the incorporation of Al and O was found to be independent of x, but the compensation of Si donors decreases with increasing In content. Deep level transient spectroscopy analysis on a series of In_xGa_1-xAs: Si. samples with 0 ≤ x ≤ 0.18 revealed that oxygen incorporation led to a set of deep levels, similar to those found in DEALO doped GaAs. As the In composition was increased, one or more of these deep levels became resonant with the conduction band and led to a high electron concentration in oxygen doped In_0.53Ga_0.47As. Low temperature photoluminescence emission measurements at 12K on the same set of samples revealed the quenching of the near-band edge peak, and the appearance of new oxygen-induced emission features. DEALO doping in InP has also led to the incorporation of Al and O, and the compensation of Si donors due to oxygen-induced multiple deep levels.     

东营深层盐膏层钻井液工艺

胜利油田东营深层盐膏地层发育,盐膏段厚度大,分布范围广,地层岩性十分复杂,钻井中经常发生喷、漏、塌、卡,遇阻、划眼、电测遇阻等井下复杂事故。郝科1井是在该区设计的一口重点深探井,宅钻井深5807.81m,井底最高温度230℃。介绍了深层盐膏层钻井液体系的转化工艺、性能控制、维护处理、防漏、堵漏、固相控制、抗污染和钻具缓蚀等技术,以及MMH聚合物饱和盐水钻井液在郝科1井的成功应用。结果表明,该钻井液在高密度下对盐膏层具有较强的抑制性、悬浮携砂性和抗污染性,抗温220—230℃。MMH聚合物饱和盐水钻井液体系及其配套技术满足了深层盐膏层钻井施工需要。     

Development of ultra light magnesium-lithium alloys

Magnesium-lithium alloys are among the lowest density metallic materials. Addition of lithium, with a relative density of 0·53, in magnesium reduces the density of the alloy significantly. Furthermore, addition of nearly 11 wt.% lithium converts hexagonal close packed structure of pure magnesium to a body centered cubic lattice, markedly improving formability of the alloy. The development of these alloys, however, had been hampered due to the high reactivity of lithium and magnesium in the molten state and also, due to poor creep resistance and instability of mechanical properties at room temperature. In an attempt to indigenize these ultra light alloys for possible applications in Indian satellite programme, detailed research work was initiated in DMRL. The difficulties associated with producing sound cast ingots have been overcome by controlling melting and casting parameters of these alloys. Extensive work has been done on structure-property correlation of alloys with varying lithium content and minor alloying additions. Based on these work, advanced magnesium-lithium alloys have been developed with improved tensile properties, room temperature stability and creep resistance. Wrought products (plates/sheets) of magnesium-lithium alloy have been supplied to ISAC, Bangalore and are being used in their INSAT-2 programme. This paper describes the systematic studies carried out in the laboratory to indigenize these ultra light alloys.