MPLS交换路由器的设计与实现

MPLS是目前Internet核心网上最看好的技术，基于Crossbar的高速交换技术的发展也很快，但是如何实现2种技术的有机结合以到达最优的性能却有一系列问题需要考虑。本文结合某MPLS路由器的设计项目，综合考虑了当前MPLS的标准以及有关交换结构的最新技术，对实现MPLS交换路由器进行了深入研究，并详细探讨了高速接口、排除和调度以及Crossbar等关键模块的设计和实现方案。     

大型居住区设计探索——“深圳市新亚洲花园”设计回顾

通过对大型住宅区“深圳市新亚洲花园”工程规划及建筑方案创作构思的分析,实现住宅提升人们生活品质的设计思想,同时,在规划设计上对住宅开发在经济市场上如何提升竞争力做了有益探索。     

Symmetric BEM formulations for 2-D steady-state and transit potential problems

This paper presents a new concept for symmetric boundary element method (SBEM) applicable to 2-D steady-state and transit potential problems. Two kinds of SBEM formulations are derived. Symmetry is obtained simply through matrix manipulation, and no hypersingularity appears. Therefore, SBEM is much easier than the traditional symmetric Galerkin BEM. Compared with the traditional asymmetric BEM, the present SBEM can reduce the computational cost for time domain problems only. However, when applied to BEM/FEM coupling procedure, SBEM can reduce the computational cost for both steady-state and time domain problems. Three numerical examples are included to illustrate the effectiveness and accuracy of the present formulations.     

Investigation of structural properties of ITO thin films deposited on different substrates

The influence of the substrate nature on the structure and morphology of ITO thin films grown by thermal evaporation in vacuum is investigated. The as-prepared metal films with Sn/In molar ratio of 0.1 were subsequently annealed for 2 h at 723 K in air (to obtain tin doped indium oxide), then annealed in vacuum at 523 K, followed by UV irradiation (to reduce the electrical resistivity). Irrespective of substrate nature, XRD data evidence a (222) preferential orientation in films. Substrate nature, annealing in vacuum and UV irradiation influence the structure, morphology, optical, electrical and surface wetting properties of the films' surface.     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

高温对冶金窑窑体的影响

针对冶金回转窑窑体在高温下产生的失效进行数值分析，并在此基础上对冶金窑窑体的设计方法进行修正。     

常门铺水库溢洪道设计方案比较

在常门铺水库溢洪道改造中，通过不工模型试验，对其数据成果进行分析并进行方案比较，最终采用即经济又合理的方案二，为国家节省投资50.8万元。     

爱立信/Juniper路由器集群方案介绍

首先简要介绍了集群技术和路由器集群方案,重点说明了其核心——交换网络的结构及其原理,最后对该方案的优点进行了归纳、总结。     

杭-宁输气管道工程定向钻穿越设计浅析

杭州-宁波天然气输气管道工程（简称杭-宁输气管道工程）是浙江省天然气长输管网主干线之一，根据工程河流穿越众多、渠塘穿越频繁的特点，对杭-宁输气管道工程水域穿越的特点和穿越方式作了总结；重点分析了水域定向钻穿越设计及需要注意的问题，为今后浙江省天然气管网建设的水域穿越设计作了探讨。