Influence of pores arrangement on stability of photonic structures during sintering

Discrete Element Method (DEM) has been used for numerical investigation of sintering-induced structural deformations occurring in inverse opal photonic structures. The influence of the initial arrangement of template particles on the stability of highly porous inverse opal α-Al₂O₃ structures has been analyzed. The material transport, densification, as well as formation of defects and cracks have been compared for various case studies. Three different stages of defects formation have been distinguished starting with local defects ending with intrapore cracks. The results show that the packing of the template particles defined during the template self-assembly process play a crucial role in the later structural deformation upon thermal exposure. The simulation results are in very good agreement with experimental data obtained from SEM images and previous studies by ptychographic X-ray tomography.     

Damage identification in concrete using impact non-linear reverberation spectroscopy

High amplitude non-linear acoustic methods have shown potential for the identification of micro damage in brittle materials such as concrete. Commonly, these methods evaluate a non-linearity parameter from the relative change in frequency and attenuation with strain amplitude. Here, a novel attenuation model is introduced to describe the free reverberation from a standard impact resonance frequency test, together with an algorithm for estimating the unknown model coefficients. The non-linear variation can hereby by analyzed over a wider dynamic range as compared to conventional methods. The experimental measurement is simple and fully compatible with the standardized free-free linear impact frequency test.     

THE effect of Srandom DOPANT fluctuation on threshold voltage and drain current variation in junctionless nanotransistors

We investigate the effect of dopant random fluctuation on threshold voltage and drain current variation in a two-gate nanoscale transistor. We used a quantum-corrected technology computer aided design simulation to run the simulation (10000 randomizations). With this simulation, we could study the effects of varying the dimensions (length and width), and thicknesses of oxide and dopant factors of a transistor on the threshold voltage and drain current in subthreshold region (off) and overthreshold (on). It was found that in the subthreshold region the variability of the drain current and threshold voltage is relatively fixed while in the overthreshold region the variability of the threshold voltage and drain current decreases remarkably, despite the slight reduction of gate voltage diffusion (compared with that of the subthreshold). These results have been interpreted by using previously reported models for threshold current variability, load displacement, and simple analytical calculations. Scaling analysis shows that the variability of the characteristics of this semiconductor increases as the effects of the short channel increases. Therefore, with a slight increase of length and a reduction of width, oxide thickness, and dopant factor, we could correct the effect of the short channel.     

Fully coupled LES-DEM of particle interaction and agglomeration in a turbulent channel flow

Coupled large eddy simulation and the discrete element method are applied to study turbulent particle–laden flows, including particle dispersion and agglomeration, in a channel. The particle–particle interaction model is based on the Hertz–Mindlin approach with Johnson–Kendall–Roberts cohesion to allow the simulation of van der Waals forces in a dry air flow. The influence of different particle surface energies, and the impact of fluid turbulence, on agglomeration behaviour are investigated. The agglomeration rate is found to be strongly influenced by the particle surface energy, with a positive relationship observed between the two. Particle agglomeration is found to be enhanced in two separate regions within the channel. First, in the near-wall region due to the high particle concentration there driven by turbophoresis, and secondly in the buffer region where the high turbulence intensity enhances particle–particle interactions.     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

Correlation between motion of source bender element and feedback signal induced by self-monitoring

Since the introduction of bender element tests to soil testing, the reliability of the estimated travel time has been the most serious problem. The author has previously shown a potential solution whereby removing the response of the bender element subsystem from the whole response could dramatically improve the accuracy of the travel time estimation. In order to lay the foundation for estimating the response of the bender element subsystem, this paper examines the correlation between the displacements of the element and the induced feedback signals by employing a self-monitoring element. The response of the self-monitoring element is modeled as a transfer function involving two internal transfer functions that relate the input signals to the displacements and the displacements to the feedback signals, respectively. Using a laser displacement sensor, the displacements are directly measured through the entire surface and reveal the three-dimensional bending motion of the element oscillating in both longitudinal and width directions. The feedback signals are similar to, but inconsistent with, the tip displacements, and an attempt is made to correct the feedback signals. Finally, a conclusion is given on the potential for estimating the response of the bender element subsystem using the self-monitoring element.     

A stiffness parameter and truncation error criterion for adaptive path following in structural mechanics

We explore a truncation error criterion to steer adaptive step length refinement and coarsening in incremental-iterative path following procedures, applied to problems in large-deformation structural mechanics. Elaborating on ideas proposed by Bergan and collaborators in the 1970s, we first describe an easily computable scalar stiffness parameter whose sign and rate of change provide reliable information on the local behavior and complexity of the equilibrium path. We then derive a simple scaling law that adaptively adjusts the length of the next step based on the rate of change of the stiffness parameter at previous points on the path. We show that this scaling is equivalent to keeping a local truncation error constant in each step. We demonstrate with numerical examples that our adaptive method follows a path with a significantly reduced number of points compared to an analysis with uniform step length of the same fidelity level. A comparison with Abaqus illustrates that the truncation error criterion effectively concentrates points around the smallest-scale features of the path, which is generally not possible with automatic incrementation solely based on local convergence properties.     

大口径光学元件装夹转运结构设计及分析

为了实现大口径光学元件的安全装夹、转运,通过光学元件开槽与不开槽两种装夹方式的分析,得出开槽夹紧转运方式将带来微裂纹、应力集中、成本高等缺陷,提出了利用摩擦力克服光学零件的重力和惯性力的低应力装夹转运方案。通过对光学元件低应力夹紧结构设计,并利用有限元分析方法,得到不开槽装夹方式下,光学元件的最大主应力为1.11 MPa,最大切应力为0.73 MPa,远低于光学元件破坏的强度极限,且受力均匀,无应力集中现象。     

A case-deletion diagnostic for penalized calibration estimators and BLUP under linear mixed models in survey sampling

The penalized calibration technique in survey sampling combines usual calibration and soft calibration by introducing a penalty term. Certain relevant estimates in survey sampling can be considered as penalized calibration estimates obtained as particular cases from an optimization problem with a common basic structure. In this framework, a case deletion diagnostic is proposed for a class of penalized calibration estimators including both design-based and model-based estimators. The diagnostic compares finite population parameter estimates and can be calculated from quantities related to the full data set. The resulting diagnostic is a function of the residual and leverage, as other diagnostics in regression models, and of the calibration weight, a singular feature in survey sampling. Moreover, a particular case, which includes the basic unit level model for small area estimation, is considered. Both a real and an artificial example are included to illustrate the diagnostic proposed. The results obtained clearly show that the proposed diagnostic depends on the calibration and soft-calibration variables, on the penalization term, as well as on the parameter to estimate.