大冶硫酸四系列干吸塔结构特点

以干燥塔为例，介绍大冶公司硫酸四系列干吸塔的结构特点。除捕沫层简体及出气管为316L不锈钢外，其余塔体均为碳钢内衬瓷砖结构。塔底为球形底，中心排酸。采用槽管式分酸器，分酸点密度为43个/m^2，设可调闸板以保证各槽酸量均匀；闸板外设置带孔板的分布板，以消除进口酸的冲击，保证槽内酸液面平稳。比较了该塔与常规塔的不同之处，强调了设备节点的优化设计。     

新型无氟发泡工艺技术改进

介绍了传统无氟发泡工艺具体工况,分析了聚氨酯泡沫存在容易产生形变、强度和韧性不高和工艺中附加物分散性不佳等问题,本文提出一种改进的无氟发泡工艺,与传统的无氟发泡工艺相比,改进的无氟发泡工艺能有效解决聚氨酯泡沫易形变的问题,提高了聚氨酯的强度及韧性,增加了附加物的分散性效果,降低了发泡体系设备.对进一步改善无氟发泡工艺技术具有重要意义.     

硝铵装置降膜蒸发存在问题与改进措施

对我公司硝铵装置降膜蒸发工序存在的问题进行分析 ,并通过技术改进 ,使干燥洗涤液全部返回系统 ,造粒塔粘塔问题得到缓解 ,取得可观的经济效益和环保效益     

Comparison of structural and photoluminescence properties of ZnO thin films grown by pulsed laser deposition and ultrasonic spray pyrolysis

ZnO thin films have been deposited by pulsed laser deposition (PLD) and ultrasonic spray pyrolysis (USP) method, respectively. X-ray diffraction and transmission electron microscopy characterizations indicate that ZnO film grown by PLD exhibits better crystallinity than that grown by USP. Photoluminescence spectra show that the near-band edge ultraviolet emission of film grown by PLD is narrower and shifts to higher energy, compared with that of film grown by USP. In the visible range, ZnO film grown by PLD exhibits four local level emission centered at 470 nm, 486 nm, 544 nm, and 613 nm, respectively, while the film grown by USP only presents a weak broad band emission centered at 502 nm. Hall measurement shows higher carrier density and lower hall mobility in ZnO film grown by PLD than that in film grown by USP. The higher density of intrinsic defects as well as higher crystallintiy is considered to account for the difference of photoluminescence in ZnO film grown by PLD with that in film grown by USP.     

Dynamics of electrically charged transient evaporating sprays

The evolution of an evaporating spray plume typical of those under consideration for use in direct injection spark ignition (DISI) engines, for early and late fuel injection strategies is investigated. Here the effect of electric charge, present on individual drops, upon the spray dispersal and evaporation rate is investigated with the aim of optimizing these parameters with respect to typical engine timescales and injection strategy. The predictions suggest that applying electric charge to drops in sprays injected early into the intake stroke does not have a beneficial effect. The spray evaporation rate is not significantly enhanced, and the long time interval between fuel injection and ignition actually promotes spray wall deposition. Conversely, applying electric charge to sprays injected late encourages secondary atomization and the increase in surface area greatly improves the evaporation rate. This is also true at higher engine speeds, corresponding to a much reduced time between fuel injection and ignition. Therefore it is suggested that the selective use of electric charge is viable way of tuning the spray character without effecting fuel metering when moving from an early to a late injection strategy in DISI engines when variable loads are required. Copyright © 2006 John Wiley & Sons, Ltd.     

喷射沉积柱坯的生长模型

根据现有喷射沉积设备的喷射几何关系推导了柱状沉积坯生长的数学模型,并利用该模型对沉积器的临界下降速度进行了初步估算。     

金隆闪速炉精矿喷嘴的优化

介绍金隆公司闪速炉精矿喷嘴的结构特点和运行情况,针对运行中存在的问题,通过优化操作参数、改进结构,喷嘴的性能得到了很大改善。     

武钢第一炼钢厂钢包喷补工艺的应用

以碱性喷补料的损毁机理为根据，讨论了该类型喷补料的颗粒分布和结合理论，根据操作条件提出优化方案选取相应的产品，从而获得较好的使用效果。     

模糊控制在空调清洗系统中的应用

描述了烘干罐温度模糊控制器的设计原理及控制系统的软硬件组成,由AT89C52实现的空调烘干控制系统,实现了空调清洗烘干自动化.实际运行表明,烘干系统具有控制精度高、动态响应好、可靠性高、抗干扰能力和鲁棒性强等特点.