Oxygen glow discharge experiment to remove deposited layers and to release trapped hydrogen isotopes in HT-7 superconducting tokamak

An experiment to remove re-deposited layers and to release hydrogen using a glow discharge in oxygen (O-GDC) has been performed in the HT-7 superconducting tokamak. In the absence of magnetic fields, the O-GDC wall conditioning had produced rapid, controlled co-deposit removal. Average removal rates, 5.2 × 10²² H-atoms/h, 5.65 × 10²¹ D-atoms/h and 5.53 × 10²² C-atoms/h, respectively, were obtained during 145 min O-GDC experiment in the pressure range 0.5-1.5 Pa. The corresponding removal rate of co-deposited films was ∼1.19 μm/day (26.5 g/day for carbon) based on an area of 12 m². Compared to thermo-oxidation and O-ICR experiment, high pressure O-GDC wall conditioning promoted the oxidation and improved the C and D atoms removal. In the O-GDC experiment, the removal rates of H-atoms and D-atoms as H₂O, HDO and D₂O were higher than that of H₂ and D₂ by factors of about 20 and 50, respectively. During the 145 min O-GDC experiment, about 14.5% O-atoms were converted into carbon oxides and hydroxides, and about 5.37 × 10²² O-atoms were adsorbed on the walls corresponding to a coverage of 4.5 × 10²¹ O/m² on an wall area of 12 m². In a 100 min helium glow discharge (He-GDC) following the O-GDC experiment, 1.53 × 10²² O-atoms, about 28.5% oxygen retained on the walls, were removed. The removal rate of H-atoms in He-GDC cleaning after O-GDC experiment was lower than that in He-GDC cleaning before O-GDC experiment, which indicates that the O-GDC wall conditioning had effectively reduced hydrogen retention on the walls.     

Formation of steady state size distribution of precipitates in alloys under cascade-producing irradiation

The effect of coherency loss on the development of precipitate size distribution under cascade-producing irradiation is considered. The nucleation of coherent precipitates, their growth followed by coherency loss and cascade-induced dissolution of large incoherent precipitates can occur simultaneously resulting in formation of a quasi-stationary size distribution of semicoherent precipitates. To describe this process we consider co-evolution of a mixed population of coherent, semicoherent and incoherent precipitates. Mathematically, the problem is formulated as a set of discrete rate equations of nucleation kinetics (the Master equation approach) which is also used for later stages of evolution. To solve the corresponding large set of equations (typically, more than 10⁵ equations) an efficient numerical method is developed. The simulation results obtained for material parameters and irradiation conditions typical for nuclear reactors show that the coherency loss affects considerably evolution of the precipitate population. Under certain irradiation conditions, both in solution-annealed alloys and in aged ones, the mean precipitate size and the number density during prolonged irradiation tend to steady state values, whereas the size distribution function of large precipitates narrows. The width of the quasi-stationary size distribution is controlled by cascade parameters. It was found that the asymptotic quasi-stationary state of the precipitate population may depend on initial state of the alloy.     

坨五站中间乳化层快速增长原因及治理方案

胜利采油厂坨五站高含水(95％)原油化学预脱水中，二级沉降罐内油水相之间的中间乳化层增长迅速，引起了一系列问题。现场调查和大量室内测试结果表明，产生这一现象的原因有：油溶性破乳剂WD-1加入点不合理。有2／3的含水原油在通过油水分离器之后才与破乳剂混合；二级沉降罐进油口伸入油相内，油流的冲击达不到中间层；WD-1对坨五站混合原油中的稠油破乳脱水性能欠佳，不能适应坨五站混合原油组成和含水的变化。针对上述各种原因筛选出了性能更好的一种破乳剂1916。根据确定的几种原因采取了相应的措施：将破乳剂加入点改在3个并联油水分离器之前；将二级沉降罐的进油口移到水相内；改用筛选出的破乳剂1916，结果使中间乳化层的增长受到了抑制。图2表4参2。     

Thermal expansion characteristics of a titanium modified austenitic stainless steel: measurement by high-temperature X-ray diffraction and modelling using Grüneisen formalism

The thermal expansion of a titanium modified, swelling resistant austenitic stainless steel designated as D9 is studied by measuring the lattice parameter as a function of temperature in the range 300-1300 K by high-temperature X-ray diffraction technique. The thermal expansion data thus obtained is in reasonable agreement with the typical thermal expansion values reported for similar nuclear grade austenitic stainless steels. However, at temperatures exceeding 900 K, the measured thermal expansivity exhibits a pronounced non-linear increase due partly to the precipitation of complex carbide and intermetallic phases. The high-temperature thermal expansion data obtained in the present study are augmented by modelling the low-temperature thermal expansion behaviour by Grüneisen formalism.     

我国石油开采与油井管生产概述

概略介绍了我国石油开采及其专用管材的需求情况以及油井管的生产规划和要求,对发展国内油井管特别是焊接油井管生产提出了建议。     

涤棉府绸染色条花疵病的产生和控制

本文分析了T/C府绸集色条花产生的原因。通过工艺条件和操作方法,染色条花疵病得到明显改善。     

三辊穿孔和轧管所产生的钢管壁厚极差和波浪形内螺纹

定量描述了实际生产过程中三辊斜轧穿孔所产生的钢管壁厚极差和波浪形内螺纹，初步探讨了三辊轧管机对钢管壁厚极差和波浪形内螺纹的影响。     

实时时钟芯片 M48T86 及其应用

M48T86是意法半导体公司（ST公司）生产的一种实时时钟/日历芯片。它具有精确计时、定时报警输出等功能，由于其内置128字节的非易失性RAM，因而具有功能强、使用方便等特点。文中详细介绍了M48T86的引脚功能，性能特点和主要参数，给出了其在检测系统中的应用电路和程序设计方法。     

发动机连杆螺纹孔加工质量的改进

对发动机连杆螺纹孔在攻丝过程中出现烂牙、粗糙度差等加工质量问题进行了分析，提出了解决问题的方法，使连杆的合格率行到显著的提高。     

UHF ASK/FSK 发射器 T5750 的原理及应用

T5750是ATMEL公司推出的单片UHFASK/FSK发射器芯片 ,它内含发射功率放大器、晶体振荡器、压控振荡器、相频检波器、分频器、充电泵等电路。当T5750在868～928MHz范围内工作时 ,其输出功率为8dBm ,数据速率为32kbps。文中介绍了T5750的结构功能及应用实例。