贝氏体相变理论进展近况

近年来贝氏体相变理论三个学派的研究工作均有明显进展，有些观点渐趋接近，有些观点依然存在严重分歧，各自都有亟待澄清的难题。各派间在学术上的批判反批判旨在指明探索方向和途径，发展理论，这已充分为当今相变理论研究进展事实所证明。     

Preparation of High Strength and Toughness Aramid Fiber by Introducing Flexible Asymmetric Monomer to Construct Misplaced-Nunchaku Structure

High performance fibers with high strength and toughness have great potential in composites, but contradiction between tensile strength and elongation at break makes the preparation to become a current challenge. Herein, an asymmetric structure of more flexible diamine, 3,4′-diaminodiphenyl ether (3,4′-ODA), is introduced into heterocyclic aramid (PBIA) fibers to replace rigid symmetric p-phenylenediamine (PDA). By studying the properties of copolymer (mPEBA) fibers with different ratios of diamine, it is found that the mPEBA fiber reached the optimal mechanical properties with the 30% content of 3,4′-ODA. Compared with homopolymerized heterocyclic aramid fibers, the tensile strength and elongation at break of mPEBA fiber are improved by 26.2% and 38.7%, respectively. Results of X-ray diffraction show that the introduction of 3,4′-ODA structure can increase stretchability of mPEBA fibers, improving the orientation degree during hot-drawing. Molecular dynamics simulations confirm that 3,4′-ODA structure undergoes a conformation transformation to form a straightened chain during hot-drawing, while symmetrical 4,4′-diaminodiphenyl ether (4,4′-ODA) cannot form the same conformation. The misplaced-nunchaku structure is formed based on the special meta-para position of 3,4′-ODA, achieving the synergy of high strength and high toughness.     

浅谈贵冶转炉残极加料机无液压控制及应用

转炉残极加料机是贵冶转炉重要辅助设备之一。本文分析了贵溪冶炼厂熔炼车间转炉残极加料机运行过程存在的问题。从设备管理角度出发,分析故障原因并提出改进措施。同时改变现有残极加入的方式,顺应时代趋势,实现自动化、岗位无人化操作并在一定程度上得到应用。     

轴承钢GCr15的恒温相变超塑性

研究了ＧＣｒ１５钢在Ａｃ１相变点附近的恒温超塑性特性与变形温度的关系。结果表明，与一些材料一样，该钢也存在恒温相变超塑性现象。当初始应变速率为２．５×１０＾－４ｓ＾－１时，经预调质处理的ＧＣｒ１５钢试样，在７４８℃进行超塑性拉伸试验获得最大延伸率达８００％，流动应力为２４ＭＰａ。与已有的同类研究结果相比，其延伸率提高了２００％以上。     

Zr对Cu—Zn—Al形状记忆合金相变的影响

采用示差扫描热分析(DSC)、X射线衍射及透射电镜,研究了Zr对Cu-Zn-Al合金高温相变、马氏体正逆转变以及形状记忆效应的影响。结果表明,添加Zr0.35wt-％时,能有效地抑制α,γ相析出,促进β_2→DO_3→18RM转变。(M_s-M_f)及(A_s-A_f)温度区间较窄,马氏体相变激活能最低,马氏体变体间界面的可动性好,形状记忆效应最佳。     

应变速率对中碳低温贝氏体钢强塑性的影响

摘要：为探索低温贝氏体钢的断裂行为,研究应变速率对低温贝氏体钢TRIP效应的影响,采用不同应变速率的拉伸试验对低温贝氏体钢的强塑性进行研究。利用扫描电镜（SEM）、透射电镜（TEM）及X射线衍射（XRD）等试验方法对低温贝氏体钢的微观组织、断口形貌及裂纹走向进行表征。结果表明,随着应变速率的提高,试验钢的屈服强度由771MPa上升至806MPa,抗拉强度由1554MPa上升至1606MPa,断后伸长率由13.5%下降至9.0%。主要原因是高应变速率拉伸引发的绝热温升抑制了残余奥氏体的马氏体相变,对试验钢塑性造成负面影响。     

Cu基形状记忆合金干滑动磨损研究

对Cu基形状记忆合金CuZnAl进行了干滑动磨损,采用扫描电镜观察磨损表面及磨屑.结果表明,CuZnAl合金的磨损过程受塑性变形控制,粘着与转移磨损和剥离磨损是材料失重的两种主要机制.电镜薄膜拉伸时显微裂纹尖端发生了应力诱发马氏体相变.用显微裂纹钝化作用的马氏体择优取向机制和应力诱发马氏体相变机制阐述了这种软基体高变形能力材料的耐磨本质。     

偏晶合金液-液相变过程模拟

建立了能描述在弥散相液滴形核、扩散长大、碰撞凝并及两液相空间分离等因素共同作用下，偏晶合金液-液相变过程中组织演变过程的数学模型。将计算的温度场和浓度场与控制凝固组织演变的动力学方程相耦合，模拟研究了单向冷却条件下Al-Pb合金液-液相变过程中的组织演变过程。结果表明，随着冷却的进行，液-液相变区不断由试样底部向试样顶部推进，直至贯穿整个试样。由于在凝固过程中弥散相液滴进行Marangoni迁移和Stokes运动，试样中的某些部位会出现液滴贫化、过饱和度增加和多次形核现象。     

CALCULATION OF TRANSFORMATION VOLUME FRACTION TO HQ590 HOT ROLLED STRIP STEEL DURING CONTINUOUS COOLING

On the basis of phase transformation kinetics, the transformation of γ→α,P,B have been investigated through considering the effect of deformation. The calculation methods of volume fraction have also been given. Comparing with common method, the simulated results are in more agreement with experiment results.     

EFFECT OF RESIDUAL STRESS ON THE MARTENSITIC TRANSFORMATION OF SPUTTER-DEPOSITED SMA THIN FILMS

TiNi thin films were sputter-deposited on circular single-cry stal silicon substrates un-der various sputtering parameters. The crystal structure and residual stress of the as-deposited films were determined by X-ray diffraction and substrate-curvature method. The phenomenon of stress-suppressed martensitic transformation was observed. R is considered that the residual stresses in SMA thin films based on circular substrates act as balanced biaxial tensile stresses. The status of equilibrant delays the align-ment of self-accommodated variants and the volume shrinkage during the martensitic transformation.