分子结构对增塑聚氯乙烯性能的影响

研究了聚合度、分子量分布和支化结构对增塑聚氯乙烯加工流变性能和物理力学性能的影响。结果表明，增塑ＰＶＣ的加工流变性能随聚合度的增加而恶化；拓宽分子量分布和引入支化结构均有利于加工流变性能的提高；增塑ＰＶＣ的拉伸强度随聚合度的增加而提高，而压缩永久变形却随之减小；分子量分布对物理力学性能的影响不大；支化ＰＶＣ的拉伸强度略有下降。     

乙烯基三甲基硅烷等离子体聚合反应历程

应用色谱—质谱(GC-MS)及裂解色谱-质谱(PGC-MS)测定了乙烯基三甲基硅烷等离子体聚合反应中的气体冷凝物及聚合物,研究推导了等离子体聚合反应历程。单体在气相中被电子撞击,然后扩散到基底,在基底发生链增长和链终止反应。     

Interfacial tension between coexisting polymer solutions in mixed solvents and its correlation with bulk thermodynamics: phase equilibria (liquid/gas and liquid/liquid) for the system toluene/ethanol/PDMS

Vapor pressures, phase equilibria and interfacial tensions σ were measured for solutions of poly(dimethylsiloxane) (PDMS, M_w[equals]75 kg/mol and M_n[equals]50 kg/mol) in mixed solvents of toluene (TL) and ethanol (EtOH) at 30, 40, 50 and 60 °C. The experimental ternary phase diagrams can be modeled quantitatively from the determined concentration and temperature dependent binary interaction parameters χ_ij if the experimentally inaccessible composition dependence of χ_EtOH/PDMS is adjusted. The relations between σ and the equation of state of the system differ from that applying to single solvents. The exponents as well as the amplitude prefactors of the corresponding scaling laws (e.g. the dependencies of σ on the length of the tie lines or on the hump energy, i.e. on the intrusion into the two phase regime quantified in terms of Gibbs energies) change considerably with temperature. However, this variation can be reduced significantly by normalizing the independent variables. Dividing the length of the tie lines by the length for the corresponding binary subsystem proves more efficient than the distance of these tie lines from the critical point of the ternary system relative to the maximum distance of the binary subsystem. A combined normalization does not improve the situation.     

HPVC／PP共混改性研究：Ⅲ低分子量反应性化合物作相容剂

采用低分子量反应性化合物作相容剂，即化学交联体系来改善ＨＰＶＣ／ＰＰ共混物的相容性。考察了在不同共混比下，不同化学交联体系对共混物力学性能的影响，并观察了共混物的微观形态。结果表明，采用低分子量反应性化合物作相容剂，共混物的拉伸强度提高，但冲击强度无改善。分散相尺寸减小，相间粘接得到改善。并比较了３种增容方法的效果，发现ＣＰＥ是ＨＰＶＣ／ＰＰ共混物的最佳相容剂。     

Control of the quality of polymer products in continuous reactors: comparison of performance of state estimators with and without updating of parameters

In the paper the control of the product quality in polymerization reactors is analysed in the presence of persistent perturbations (unmodeled disturbances, modeling errors), as met in industrial reactors. The free radical polymerization of methyl-methacrylate in a continuous stirred tank reactor is studied. It is shown that state estimators (Extended Kalman Filters) with constant parameters cannot give offset free performance. Criteria for the selection of a set of parameters to be updated as additional states in the filter and to evaluate their effectiveness in opposing the action of realistic perturbations are given by an analysis of the linearized model of the system. Performance of different types of estimators, including one and two-time scale filters, with and without updating of parameters, is analysed by simulation on the full order process and the predictions made by previous analysis are confirmed. In the most common case of presence of perturbations affecting the energy balance and the concentration of initiator in the reactor, offset free control of the molecular weight of the product can be achieved by means of a filter which is based only on measurements of temperature and conversion and makes an update of two parameters. In the case that also the kinetic model of the polymerization reaction is affected by errors, a two-time scale filter, which makes use also of Molecular Weight values and updates three parameters, becomes necessary to obtain offset free performance.     

Ziegler-Natta烯烃聚合催化剂进展

综述了Ziegler-Natta催化剂在乙烯聚合和丙烯聚合方面的研究开发现状，重点介绍了采用新型二醚化合物作为内给电子体的丙烯聚合催化剂的进展。随着合成树脂向功能化方向发展，开发综合性能优越的新型催化剂及给电子体将是今后的研究方向。     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

复合聚合物微粒乳液的制备与应用

对种子乳液聚合中加料方式、单体亲水性、引发剂等因素对复合微粒聚合物形成的影响作了介绍 ,总结了聚合物微粒形态预测的热力学和动力学方法。同时 ,讨论了复合聚合物微粒设计的原理并评述了其应用情况     

MODELING LIQUID MASS TRANSFER IN HIGEE SEPARATION PROCESS

Correspondence concerning this paper should be addressed to Professor Richard S.H. Mah. Hsien-Hsin Tung is now affiliated with Department of Chemical Engineering, California Institute of Technology

Penetration theory is used to describe the liquid mass transfer in Higee separation process. Within a possible range of effective areas, it is shown that the predicted mass transfer coefficients are in reasonable agreement with the estimated mass transfer coefficients. The estimated coefficients were calculated from the experimental data and the possible effective areas. Hence it is concluded the penetration theory is generally applicable to describe liquid mass transfer in Higee separation process. The comparison also suggests that liquid mixing at the junctions of packing materials may be more complete in Higee process than in traditional process.     

LLDPE及其催化剂技术进展

综述了线性密度聚乙烯（LLDPE）研究的最进展情况，特别对乙烯原位聚合工艺和后过渡金属镍、钯催化剂进行了详细的叙述，对我国LLDPE的生产提出了自己的看法。