强化三元混合熔盐的传热性能的实验研究

太阳能发电技术中传热性能的优劣影响着太阳能的利用程度。选用石墨作为强化相变材料传热性能的添加剂与三元混合熔盐（K₂CO₃-NaCl-Li₂CO₃）按照石墨质量分数为5%、10%、15%进行混合制备,使用TC3000通用型导热系数测试仪测定16种试样的导热系数。并测试经历300次循环储能、释能实验试样的导热系数循环稳定性。实验结果表明：添加石墨后的混合相变材料导热系数最高可提升至原混合材料的3.38倍,当石墨的质量分数为15%时,混合相变材料的导热系数最大。在经历300次储能、释能实验后,材料的导热系数基本保持稳定,变化浮动不高于15%。石墨作为强化材料的添加剂,可有效提升强化材料的传热性能,具有实际工程的应用价值。     

水泥窑低温有机朗肯循环联合发电技术

以某一新型二代水泥技术的7 000 t/d熟料生产线为例,单纯的采用汽水朗肯循环,存在热量回收不彻底,部分低品位余热资源无法有效回收等问题。采用汽水朗肯循环及有机朗肯循环联合发电系统的方案,结果表明：联合朗肯循环系统发电功率提高了614 kW,吨熟料发电量增加了2.1 kWh/kg,提高了8%;净发电功率提高了511 kW,净发电量实际提高了7.1%,提高了水泥余热回收的效率。     

基于DSM与QFD技术的设计联合矩阵及其决策流程

在大型复杂设计活动中，由于缺少系统化的交流机制来保障设计过程中设计信息的及时、准确地传递，产生设计冲突，进而导致整个设计在时间上的拖延。本文以此为出发点，提出了解决上述冲突的基于DSM与QFD技术的集成设计联合矩阵及其决策流程；支持企业缩短其新产品开发的周期。     

快淬工艺对无钴AB5型贮氢合金循环稳定性的影响

研究了快淬工艺对无钴AB5型LaxMm1-x(NiMnSiAlFe)4.9(x=0,0.45,0.75,1.0)合金微观结构及电化学循环稳定性的影响.结果表明快淬处理显著改善合金的成分均匀性,使晶粒细化,并显著提高合金的循环稳定性.当淬速从0m/s增加到28 m/s时,经300次充放循环后,x=0.45合金的容量衰减率D从0.28 mAh/g·c-1(c代表一次循环)下降到0.13mAh/g·c-1;x=1.0合金的容量衰减率D从0.3mAh/g·c-1下降到0.14mAh/g·c-1.     

Fe替代Co对AB5型贮氢合金循环稳定性的影响

用铸造及快淬的方法制备了稀土基AB5型Mm（NiMnSiAl）4．3Co0.6-xFex（x=0，0．1，0．2，0．3，0．4，0．5，0．6）贮氢合金，用XRD。TEM及SEM观测了铸态及快淬态的微观结构，测试了合金在铸态及快淬态下的电化学循环稳定性。研究了Fe替代Co对铸态及快淬态贮氢合金微观结构及循环稳定性的影响。研究结果表明，Fe替代Co对铸态及快淬态合金的相结构没有明显影响，但对合金的循环稳定性产生显著影响。Fe替代Co能不同程度地改善铸态及快淬态合金的循环稳定性，但对快淬态合金循环寿命的改善更加显著，导致这一结果的主要原因是Fe替代Co使快淬态合金的微观组织显著细化。     

硼对低钴AB5型贮氢合金循环寿命的影响

为了提高低钴AB5型贮氢合金的电化学循环稳定性，在低钴AB5型贮氢合金中加入微量的硼，用真空快淬工艺制备了稀土系低钴AB5型MmNi3.8Co0.4Mn0.6Al0.2Bx(x=0，0．1，0．2，0．3，0．4)贮氢合金，分析测试了铸态及快淬态合金的电化学性能及微观结构，研究了硼对铸态及快淬态合金微观结构及循环寿命的影响。结果表明，硼能大幅度提高铸态及快淬态低钴AB5型贮氢合金的电化学循环稳定性，但其作用机理是完全不同的。     

ANN valuation model of material LCIA profile

Weighting model is the only valuation model of life cycle impact assessment(LCIA) profile now. It simplifies evaluation function into linear function, and makes the determination of weighting factor complicated. Therefore the valuation of LCIA profile is the most critical and controversial step in life cycle assessment(LCA). Development on valuation models, which are understood easily and accepted widely, is urgently needed in the field of LCA.The modeling approaches for the linear evaluation function were summed up. The modeling approaches for the nonlinear evaluation function were set up by function approximation theory, which include choosing preference products, forming preference data, establishing artificial neural network(ANN) and training ANN by preference data.By selecting 7 material products as preference product, experience was done with modeling approaches of the nonlinear evaluation function. The results show that the modeling approaches and valuation model of the nonlinear evaluation function are more practical than the weighting model.     

High cycle fatigue behaviour of Ti–6Al–4V alloy at elevated temperatures

High cycle fatigue behaviour of Ti–6Al–4V alloy was studied at 623 K and 723 K. Fatigue strength decreased at elevated temperatures compared with at ambient temperature. In the short life regime, fatigue strength was lower at 723 K than at 623 K, but in the long life regime it was nearly the same at both temperatures. At elevated temperatures, cracks were generated earlier at applied stresses below the fatigue limit at ambient temperature, indicating lowered crack initiation resistance. Small cracks grew faster at elevated temperatures than at ambient temperature, which became more noticeable with increasing temperature. After allowing for the elastic modulus, small cracks still grew faster at elevated temperatures.     

GH4169缺口件多轴加载下应力应变场的有限元分析

采用GH4169缺口试件在650 ℃下进行了高温拉扭疲劳断裂试验,利用ANSYS 6 1 有限元分析软件计算试件缺口周围的应力应变场,确定出试件在各种载荷状况下的应力集中系数。计算结果表明,该有限元建模方式是合理的,为以后缺口件的寿命预测过程奠定了基础。     

九江大化肥Shell之碳黑回收技术探讨

对九江大化肥厂Shell渣油气化碳黑闭路循环和石脑油萃取碳黑的成熟可靠性等技术问题进行了探讨。