熔渣法碳化铬涂层的抗氧化性能研究

对熔渣法碳化铬涂层在各种温度下经20h和200h的氧化性能进行了研究，与常用的一些锅炉用钢进行了对比试验，结果表明碳化铬涂层抗氧化性能比15CrMo、102、T91钢好，可以与TP347钢相媲美。     

Preparation and electrochemical performance of nanosized Co3O4 via hydrothermal method

The hydrotalcite-type cobalt compounds were prepared through oxidation of Co（OH）2 gel using NH4OH as precipitating agent and H2O2 as oxidant. These hydrotalcite-type cobalt compounds were transformed into Co3O4 through hydrothermal decomposition with nanostructural deformation. The precursor and product were characterized by Fourier-transform infrared（FT-IR） spectrum, X-ray diffractometry（XRD） and transmission electron microscopy（TEM）. The electrochemical performances of as-prepared nanosized Co3O4 as anode materials in lithium-ion batteries were tested by charge-discharge test in the voltage range of 0-3.0 V. The influence of morphology of Co3O4 particle on the capacity and cycling performance was studied. The results show that the shape and size of the final product can be controlled by altering cobalt sources. The irregular cubic Co3O4 with the average particle size of about 10 nm shows the best electrochemical performance. After 10 charge-discharge cycles, the specific charge capacity retains 555 mA.h/g.     

体积成形有限元模拟软件CASFORM的开发研究

简要介绍了作者自主开发的体积成形有限元模拟软件CASFORM及其关键技术，并给出了大量的实例分析。CASFORM主要由前处理模块，有限元分析模块，后处理模块，有限元网格生成模块和网格再划分及数据传递模块以及材料数据库和模拟数据库等构成，该软件能够分析各种体积成形工艺，包括锻造、挤压、拉拔等。能够预测缺陷的生成，验证和优化工艺/模具设计方案，该软件既能模拟等温成形过程，也可以模拟非等温成形过程，即可进行单工位成形分析，也可进行多工位成形分析。该软件界面友好，使用方便，可靠性和自动化程度高，是模具和工艺设计方案验证和优化的有力工具。     

型材产生壁厚偏差的原因及解决方法

就型材生产过程中产生壁厚偏差的原因进行了分析，并就解决偏差的方法进行了探讨。     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

划痕法测Ni—P合金镀层结合力的研究

本文用划痕法测定了Ni-P合金镀层的结合力;观察了划痕侧面镀层的失效形式;分析了三种评定结合力的参数。结果指出,临界载荷L_C、平均应力σ_A用于评定Ni-P镀层的结合力是有条件的,而B-W公式存在的问题更多。     

纯铜动态再结晶的Monte Carlo法模拟

本文建立了一种基于能量判据的确定动态再结晶各个阶段临界应变的方法，并基于此种方法Monte Carlo(MC)法进行了纯铜动态再结晶的二维模拟，定量计算了变形引起的存储能与变形之间的关系，计算出了发生动态再结晶的临界应变。模拟结果表明，采用MC法可以揭示动态再结晶的形核生长过程与应变历史之间的关系。结合本文所建立的基于能量判据的确定动态再结晶各个阶段临界应变的方法，可以预测开始发生动态再结晶的临界变形条件。     

Modelling of plastic flow, heat transfer and microstructural evolution during rolling of eutectoid steel rods

A study was undertaken in an attempt to quantitatively describe the rolling process of eutectoid steel rods. Finite element method was employed to model plastic flow and heat transfer in the deformed material, and heat transfer during cooling to ambient temperature. The numerical calculation gave an assessment of the strain, strain rate and temperature distributions in the work piece. This allowed the prediction of the austenite microstructure evolution during the process. Finally, the relationships describing the microstructure-mechanical properties were used to quantitatively characterize the influence of processing parameters on strength of rods after rolling.     

电子束焊接工艺参数与温度场的关系

采用有限元方法,定量分析了电子束焊接工艺参数与铍环内表面温度的关系。结果表明,加热深度或电子束斑点半径增加,内表面温度增加,焊接速度增加,内表面温度降低。     

基于弹塑性有限单元法的齿轮轴数值模拟

基于弹塑性有限单元法的一般原理,建立了齿轮轴热处理的热力耦合分析模型,对12Cr齿轮轴热处理工艺中温度、应力以及相变的分布情况进行了模拟,研究了加热规范的成形性,并与实际结果比较证实本模型的有效性,为有限单元法在热处理工艺模拟中的应用奠定了一定基础。