Synthesis,Properties, and Photopolymerization of Liquid‐Crystalline Oxetanes: Application in Transflective Liquid‐Crystal Displays

Mixtures of liquid‐crystalline di‐oxetanes and mono‐oxetanes are made for the purpose of making birefringent films by photopolymerization. The composition of a di‐oxetane mixture that forms spin‐coated films of planarly aligned nematic monomers is reported. These films are photopolymerized in air. The molecular order of the monomers can be changed on the microscale to form thin films with alternating birefringent and isotropic parts by using a combination of photopolymerization and heating. The interface observed between the birefringent and isotropic 10 μm × 10 μm domains is very sharp and the films show hardly any surface corrugation. In addition, the polymerized films are thermally stable, making them very suitable for use as patterned thin‐film retarders in high‐performance transflective liquid‐crystal displays (LCDs) which satisfy customer demand for displays that are brighter and thinner and that deliver better optical performance than conventional LCDs with an external non‐patterned retarder.     

液闪测氡中闪烁杯的氡气泄漏

本文简要介绍了液闪测氡中氡气自闪烁杯泄漏的实验结果。实验中对三种玻璃闪烁杯盖的密封性能作了检查,结果表明,这三种闪烁杯均不能满足液闪法测氡中对氡的密封要求。采用一层1mm 厚的橡胶垫片和一层0.01mm 厚的铝化聚脂膜作衬垫,代替原来的聚乙烯或纸板衬垫,解决了其中两种闪烁杯的氡气泄漏问题。建议在使用商品闪烁杯测氡时,应首先检查其对氡的密封性,必要时需采取补救措施,以保证测量结果的可靠性。     

Integration of solvent extraction and liquid membrane separation: An efficient tool for recovery of bio-active substances from botanicals

An integrated process based on simultaneous solid-liquid extraction and liquid membrane separation is proposed for recovery and isolation of valuable species from botanicals. This integration provides complete exhausting of the solid material even in the case of very low solubility of the specified solute in the extracting solvent. Selectivity of the liquid membrane ensures a preferential transport of the desired solute from the native extract into the strip solution, while the other co-extracted species remain predominantly in the native extract.     

Effect of Plate Oscillation on Bubble Residence Time in an Aerated Stagnant Liquid

Gas transfer efficiency during absorption is an important factor in various technological processes involving the interaction between liquid and gaseous systems. It is known that gas bubble motion characteristics strongly affect the efficiency of mass transfer during gas absorption. A device for mechanical vibration of an aerated liquid was designed, based on a cylindrical column filled up with tab water and a plate oscillating in the vertical direction. The goal of the present study is to investigate the effect of vibration parameters such as amplitude, frequency and form of the applied signal on the efficiency of the oxygenation process. Bubble residence time in the liquid and bubble depth of submergence related to the oscillating plate surface were chosen as main parameters for measurements. Furthermore, experiments were conducted to study the effect of the design parameters of the vibrating plate on bubble motion characteristics. The resultant data show that bubble residence time and depth of submergence can be controlled by changing the amplitude, the frequency and the form of the vibration field applied.     

Liquid phase epitaxial growth of pure and doped GaSb layers: morphological evolution and native defects

Undoped and Te-doped gallium antimonide (GaSb) layers have been grown on GaSb bulk substrates by the liquid phase epitaxial technique from Ga-rich and Sb-rich melts. The nucleation morphology of the grown layers has been studied as a function of growth temperature and substrate orientation. MOS structures have been fabricated on the epilayers to evaluate the native defect content in the grown layers from theC-V characteristics. Layers grown from antimony rich melts always exhibitp-type conductivity. In contrast, a type conversion fromp- ton- was observed in layers grown from gallium rich melts below 400 C. The electron mobility of undopedn-type layers grown from Ga-rich melts and tellurium doped layers grown from Sb- and Ga-rich solutions has been evaluated. Paper presented at the poster session of MRSI AGM VI. Kharagpur. 1995     

Heat transfer and flow of He II in narrow channels

Heat transfer and fluid flow of He II in a long, narrow channel connected to a bath that supplies a constant supply of heat have been investigated by numerical simulations by using the simplified model of Kitamura et al. [Cryogenics 37 (1) (1997) 1]. Such channels are used to cool compact, stable, low-temperature magnets. The fluid flow is driven by natural convection and the mutual friction between the normal fluid and the superfluid.In this model, the thermomechanical effect and the Goter-Mellink mutual friction balance each other. A consequence of this balance is that the velocity and temperature distributions of He II can be characterized by a dimensionless, dependent parameter equal to the ratio of the fluid speeds of internal convection to the total fluid flow. After a sudden application of heat flux, the internal convection dominates over the total fluid flow until the establishment of steady-state temperature gradients. This predicts that the time required to set up the steady-state total fluid flow is proportional to the total heat capacity in the channel.     

Filtration of liquid aerosols with a horizontal fibrous filter

The aim of this study was to determine the filtration efficiency and pressure drop in liquid aerosol capture mechanisms using a fibrous coalescent filter. The experimental set-up was designed to measure filtration efficiency and pressure drop through the filter. To avoid the gravimetric effect, the filter was placed horizontally. A series of experiments highlighted the importance of operating conditions such as filtration velocity and aerosol concentration. The results demonstrated the advantage of working at high velocities to minimise the resistance of the medium and to enhance the mass efficiency of the coalescent filter. In parallel, no effect of aerosol concentrations in the pressure drop increase was noted.     

Matrix mediated alignment of single wall carbon nanotubes in polymer composite films

Alignment of single wall carbon nanotubes (SWNT) in liquid crystalline (LC) polymer matrix imparting orientation to the nanotubes along the nematic director was studied by atomic force microscopy, measurements of electrical conductivity and Raman spectroscopy of the composite in the directions parallel and perpendicular to the nematic director. The composites were prepared through dispersion of SWNT with LC monomer in a common solvent, their alignment in nematic monomer and consequent UV polymerization of the monomer. The anisotropy of electrical and optical properties of the system depends strongly on the concentration of the nanotubes in the range of 1-10% SWNT being especially strong for smaller concentrations and negligible at higher loads. A simple semi-quantitative model is suggested to account for the orientational behavior of nanotubes in nematic matrices. It successfully describes the observed anisotropy of physical properties at microscale (up to 200 μm) in terms of anchoring of the polymer chains to the nanotubes surface and adjustment of the nanotubes orientation to the nematic direction due to such coupling. The increasing disorientation of the nematic domains at higher nanotubes loads is explained as a development of larger number of LC defects induced by the nanotubes in the nematic matrix due to their intrinsic nature of aggregation. The anisotropy of physical properties at macro scale (several millimeters) is much smaller and less dependable on SWNT concentration because differently oriented LC domains effectively wash out the anisotropy.