温度计量技术进展近况

近年来，在把ITS－90更方便地传递到工作用温度计，温度测量仪表采用信息技术和特殊工业场合测温应用方面均取得了一些进展。本文介绍了国内外温度技术在这些方面进展的状况。对温度定点，校验器，热电偶和热电阻测温，辐射测温，光纤测温和信息时代自动化系统中的温度检测仪表的重要进展分别作了介绍。     

A novel compact circuit for 4-PAM energy-efficient high speed interconnect data transmission and reception

Transmission of signals, whether on-chip or off-chip, places severe constraints on timing and extracts a large price in energy. New silicon device technologies, such as back-plane CMOS, provide a programmable and adaptable threshold voltage as an additional tool that can be used for low power design. We show that one particularly desirable use of this freedom is energy-efficient high-speed transmission across long interconnects using multi-valued encoding. Our multi-valued CMOS circuits take advantage of the threshold voltage control of the transistors, by using the signal-voltage-to-threshold-voltage span, in order to make area-efficient implementations of 4-PAM (pulse amplitude modulation) transceivers operating at high speed. In a comparison of a variety of published technologies, for signal transmission with interconnects of 10-15 mm length, we show up to 50% improvement in energy for on-chip signal transmission over binary encoding together with higher limits for operating speeds without a penalty in circuit noise margin.     

The effect of ambient temperature on the sensitivity of hot-cathode ionization gauges

We measured the sensitivities of five hot-cathode ionization gauges for ambient laboratory temperatures between 23 and 31 °C. All of the ionization gauges exhibited very similar behavior, and the sensitivity could be adequately modeled with a linear function of temperature. The slopes of the fits were smaller than one would expect due to changes in the calibration chamber number density. The thermal transpiration effect, due to local heating of the gauge structures, can account for this, and a characteristic gauge tube temperature can be inferred from the temperature dependence of the sensitivity. A recent comparison of the high vacuum standards of several National Metrology Institutes (NMIs) was performed over the range of 10⁻⁶-10⁻³ Pa using hot-cathode and spinning rotor gauges as transfer standards. Among the participants, laboratory temperatures varied by as much as 5 °C. It is necessary to know how laboratory temperature affects the sensitivity of the hot-cathode transfer standards (spinning rotor gauges explicitly account for the gas temperature) so that individual laboratory results can be corrected to a common temperature.     

�����������������������������ܿ��������о�

白马庙气田蓬莱镇气藏储层致密 ,孔隙结构复杂 ,非均质性强 ,单井产能低 ,研究储层特征和受控因素 ,加强储层改造方是气藏效益开发的出路。储层精细研究揭示 ,气井产能受沉积相和构造条件控制 ;高、中产井与大而厚、物性好的河口坝、河道砂坝沉积微相有关 ,纵向上具很强的层段性 ,主产层集中在Ⅳ～③、Ⅲ～③两套砂组 ,其钻探成功率分别达 82 %和 10 0 % ;平面上多分布于主体构造和东南鼻状突起 ,二者高、中产能井分别占 30 %和 70 %。在深入的地质研究和储层压裂评层选井的基础上 ,采用多层打开、分层压裂、多层合采的方法可提高气井产能 ,并形成了一套行之有效的压裂评层选井的综合配套技术。采用该技术优选出 19口井 ,已实施 5口井全获成功 ,气产量成倍或十几倍增加 ,其中白浅 4 5井气无阻流量高达 18× 10 4m3 /d ,白浅 38井投产 16 5d净增产值 10 0余万元     

关于沥青针入度指数

介绍了沥青针入度指数(PI)的由来和计算、使用意义、局限性和分析。     

Low temperature synthesis of aluminium titanate by an aqueous sol-gel route

Formation of aluminium titanate (AT) has been achieved at low temperature through sol-gel process using boehmite and titanium hydroxide as precursors by controlling the particle size at nanoscale followed by in-situ peptisation. The formations of AT phase, particle size distributions, sintering and thermal expansion characteristics, and microstructural features have been reported. DTA and XRD analysis have been performed to confirm the formation of AT. A 94% relative density was obtained for aluminium titanate sintered at 1550 °C with controlled grain size in the range of 2-3 μm.     

Modeling of Temperature–Frequency Correlation Using Combined Principal Component Analysis and Support Vector Regression Technique

A good understanding of environmental effects on structural modal properties is essential for reliable performance of vibration-based damage diagnosis methods. In this paper, a method of combining principal component analysis (PCA) and support vector regression (SVR) technique is proposed for modeling temperature-caused variability of modal frequencies for structures instrumented with long-term monitoring systems. PCA is first applied to extract principal components from the measured temperatures for dimensionality reduction. The predominant feature vectors in conjunction with the measured modal frequencies are then fed into a support vector algorithm to formulate regression models that may take into account thermal inertia effect. The research is focused on proper selection of the hyperparameters to obtain SVR models with good generalization performance. A grid search method with cross validation and a heuristic method are utilized for determining the optimal values of SVR hyperparameters. The proposed method is compared with the method directly using measurement data to train SVR models and the multivariate linear regression (MLR) method through the use of long-term measurement data from a cable-stayed bridge. It is shown that PCA-compressed features make the training and validation of SVR models more efficient in both model accuracy and computational costs, and the formulated SVR model performs much better than the MLR model in generalization performance. When continuously measured data is available, the SVR model formulated taking into account thermal inertia effect can achieve more accurate prediction than that without considering thermal inertia effect.     

非电量微机采集系统

实现水电厂电量快速微机巡回检测，温度采集较其它信号更为困难，本文着重讨论温度信号转换及与微机系统的连接。且介绍某水电厂微机控系统中非电量检测装置的硬件结构和软件编制。     

热镀钢丝膜层的冷凝计算

分析了热镀钢丝自液池引出过程中的热传导，得出了温度分布的解析解，从而计算钢丝表面膜层达到凝固温度时的提抽高度，为结构设计及确定冷却装置的合理位置提供依据。     

正交双频光栅CCD系统剪切干涉测量二维温度场

以半导体激光器为光源，利用正交双频光栅（ＯＤＦＧ）ＣＣＤ系统剪切干涉对带平板边界的半圆柱体热源的二维温度场进行实时诊断，分析剪切干涉图时，用柱函数系作为拟合基底，给出二维自然对流温度场的定量分布。