DOUBLE LOOP ACTIVE VIBRATION CONTROL OF PNEUMATIC ISOLATOR WITH TWO SEPARATE CHAMBERS

A newly designed pneumatic spring with two separate chambers is promoted and double-loop active control is introduced to overcome the following drawbacks of passive pneumatic isolation: (1)The low frequency resonances introduced into the system; (2)Conflict between lower isolation frequency and stiffness high enough to limit quasi-static stroke; (3) Inconsistent isolation level with different force load. The design of two separate chambers is for the purpose of tuning support frequency and force independently and each chamber is controlled by a different valve. The inner one of double-loop structure is pressure control, and in order to obtain good performance, nonlinearities compensation and motion flow rate compensation (MFRC) are added besides the basic cascade compensation, and the influence of tube length is studied. The outer loop has two functions: one is to eliminate the resonance caused by isolation support and to broaden the isolation frequency band by payload velocity feedback and base velocity feed forward, and the other is to tune support force and support stiffness simultaneously and independently, which means the support force will have no effect on support stiffness. Theoretical analysis and experiment results show that the three drawbacks are overcome simultaneously.     

A new and applicable method to calculate mass and heat transfer coefficients and efficiency of industrial distillation columns containing structured packings

Most of the methods developed for efficiency estimation of distillation columns were based on the empirical mass transfer and hydraulic relations correlated to laboratory data. Therefore, these methods cannot estimate efficiency of industrial columns with sufficient accuracy. In this paper, a new and applicable method was developed for calculation of efficiency (and mass and heat transfer coefficients) of distillation columns containing structured packings. This method has potential advantages; e.g., it can calculate efficiency without using any empirical mass transfer and hydraulic correlations and models, and without the need to estimate the operational and hydraulic parameters of column. Therefore, it will be free of errors, limitations, and complexities of such empirical items. In addition, precision of the method does not decrease with increasing complexity of operating conditions and design parameters of column. The method can be used for efficiency calculation of any structured packing, including new ones, in distillation columns.     

A numerical study on the performance of PEMFC with wedge-shaped fins in the cathode channel

The gas flow field design has a significant influence on the overall performance of a proton exchange membrane fuel cell (PEMFC). A single-channel PEMFC with wedge-shaped fins in the cathode channel was proposed, and the effects of fin parameters such as volume (0.5 mm³, 1.0 mm³, and 1.5 mm³), number (3, 5, and 9), and porosity of the gas diffusion layer (GDL) (0.2, 0.4, 0.6, and 0.8) on the performance of PEMFC were numerically examined based on the growth rate of power density (GRPD) and polarization curve. It was shown that wedge-shaped fins could effectively improve the PEMFC performance. With an increase in fin volume, the distributions of oxygen mass fraction in the outlet area of the cathode channel were lower, the drainage effect of the PEMFC improved, and GRPD also increased accordingly. Similar results were obtained as the number of fins increased. The GDL porosity had a greater effect than the wedge-shaped fins on the improvement in PEMFC performance, but the influence of GDL porosity weakened and the GRPD of porosity decreased as the porosity increased. This study provides an effective guideline for the optimization of the cathode channel in a PEMFC.     

Droplet Evaporation on a Hydrophilic Mesh Considering Their Sunken Shapes in Holes

The evolution of droplet shapes on a hydrophilic copper mesh was studied by using high-speed microscopic imaging technology. When a water droplet wets a hydrophilic mesh, the liquid-vapor interface initially adopts a convex shape, named as the “first darkness”. Then, as the water evaporates, the liquid-vapor interface flattens, and then it gradually adopts a concave shape; meanwhile, a “second darkness” forms. Taking the shapes of droplets sunken in holes into consideration, the quantitative liquid-vapor interface area was acquired. The evaporation coefficient becomes lower and more reasonable when considering the area increase due to the pentahedron sunken liquid in the holes. A speculation was employed to understand the observed evaporation behavior and the overprediction of the evaporation coefficient.     

机床液压碰撞防护装置的研究

就液压碰撞防护装置及试验情况向读者做扼要的介绍,得出回转运动质量的能量占碰撞总能量的大部分,而直线运动质量所占比重很小,从而为设计液压碰撞防护装置提供了依据。     

Microstructure and characterization of Ag1−xLixNbO3 ceramics

Silver–lithium niobate, Ag_1−xLi_xNbO₃, is a promising candidate for lead-free piezoelectrics. Ceramic samples for x equal 0.01, 0.02, 0.03, 0.04, 0.05, 0.06, 0.08 and 0.1 were synthesized by solid state reaction. Room temperature X-ray studies indicate that all samples consist mainly of perovskite phase. Only small amounts of secondary phases, namely Ag₂Nb₄O₁₁, Ag and LiNbO₃, appear. For x≈0.06 the orthorhombic–rhombohedral morphotropic phase boundary is observed. Excellent piezoelectric properties, recently reported for x>0.1, may be the result of proximity of morphotropic phase boundary. Scanning electron microscopy and secondary ion mass spectroscopy investigations suggest that the secondary phases occur chiefly at the grain boundaries. Dielectric measurements, carried out in a wide temperature range, revealed that Ag_1−xLi_xNbO₃, for x≤0.05, undergoes the same complex sequence of phase transitions as AgNbO₃. On the other hand, for x>0.06, the temperature dependence of dielectric permittivity exhibits only two maxima, related to transitions from the ferroelectric R phase to the antiferroelectric M phase and followed by the paraelectric O phase. The dielectric results obtained confirm the existence of the morphotropic phase boundary.     

聚合用四氟乙烯气体中微量杂质的色谱分析改进

四氟乙烯中各种微量气体成分及其含量大小的分析,一直是影响和制约聚合物质量的因素之一。随着国内外四氟加工行业对聚四氟乙烯质量要求的不断提高,为适应客户要求四氟乙烯分析的灵敏度和准确度要不断改进提高,经过一定时期的摸索优化分析方法,确定了较准确可靠的分析方法,从而取得了可喜的效果。     

A numerical study of stir mixing of liquids with particle method

The process of stir mixing of two viscous liquids is simulated using the moving particle semi-implicit (MPS) method. A mixing rate is defined within the particle method to characterize the level of mixing, as the number, position, period, and rotating speed of the stirring stick(s) and liquid viscosity are changed. The motions of liquid particles are tracked to reveal the flow field and mixing mechanisms. The variation of the mixing rate shows that the mixing rate is higher when the sticks are rotating monotonically at high speed, and an optimum position of the stick can be identified. The mixing rate does not enhance significantly when three or more sticks are employed, and the liquid viscosity has minor influences on the mixing rate. These results give useful qualitative suggestions on controlling the mixing rate during chemical reactions.     

Direct measurement of mass transfer around a single bubble by micro-PLIFI

In this paper, an original direct and non-intrusive technique using Planar Laser Induced Florescence with Inhibition (PLIFI) is proposed to quantify the local mass transfer around a single spherical bubble rising in a quiescent liquid. The new set-up tracks the mass transferred in the bubble wake for a plane perpendicular to the bubble trajectory instead of a parallel plane as in previous works, thus avoiding optical reflection problems. A spherical bubble is formed in a glass column containing fluorescent dye. A camera with a microscopic lens is placed underneath the column to record cross-sections of the transferred oxygen. A high-speed camera is located far from the column to simultaneously record the bubble position, size, shape and velocity. The dissolved gas inhibits the fluorescence so that oxygen concentration fields can be measured. From this, a calculation method is developed to determine mass transfer on the micro-scale. Experimental results are compared to the Sherwood numbers calculated from the Frössling and Higbie models used for fully contaminated and clean spherical bubbles, respectively. Results show that all experimental Sherwood numbers occur between the two models, which gives credence to the measurements. The new technique is then developed for bubble diameters ranging from 0.7 to 2 mm in six hydrodynamic conditions (1<Re<10², 10²<Sc<10⁶).     

以党的群众路线引领职工生活保障工作

群众路线是党的生命线和根本工作路线,在党的群众路线教育实践活动中,抓好职工生活保障工作,为民所思、所为,是落实党的群众路线具体体现。新形势下职工生活保障工作具有工作对象的群众性,工作原则的务实性,工作内容的多样性。因此,必须以党的群众路线引领职工生活保障工作,在谋划、推动、完善上下工夫,只有这样才能保证党的群众路线真正得到落实。