流动微量量热法研究阴离子表面活性剂在油砂表面的吸附

用流动微量量热法研究了十二烷基硫酸钠(SDDS)和十二碳羧酸钠(SL)在克拉玛依油田九区和乌尔禾区油砂上的吸附,简要地计论了吸附机理。所得实验结果表明,SL 在油砂上的吸附强度比 SDDS 的要大,在相当低的浓度下即可迟到饱和吸附。     

粘土作为高放废物处置回填材料的可行性研究

本文以西北粘土为对象,对其压实行为、热传导、膨胀特性,以及吸附和渗透性能进行了初步研究,借以探讨西北粘土在高放废物处置中用作回填材料的可行性。试验表明,以西北粘土为基材,经过适当的热改性和吸附改性,在初始含水量约为9%,于70MPa 下成型,用作高放废物处置中的回填材料是可行的。     

GaAlInP发光材料计算的经验公式

根据已经发表的实验数据，针对镓铝铟磷发光材料的提出了一组经验公式及相应的曲线，作为ＧａＡｌＩｎＰ可见光材料设计的依据或参考。     

Integrating neural network technology and noise analysis

The integrated use of neural network and noise analysis technologies offers advantages not available by the use of either technology alone. The application of neural network technology to noise analysis offers an opportunity to expand the scope of problems where noise analysis is useful and unique ways in which the integration of these technologies can be used productively. The two-sensor technique, in which the responses of two sensors to an unknown driving source are related, is used to demonstration such integration. The relationship between power spectral densities (PSDs) of accelerometer signals is derived theoretically using noise analysis to demonstrate its uniqueness. This relationship is modeled from experimental data using a neural network when the system is working properly, and the actual PSD of one sensor is compared with the PSD of that sensor predicted by the neural network using the PSD of the other sensor as an input. A significant deviation between the actual and predicted PSDs indicate that system is changing (i.e., failing). Experiments carried out on check valves and bearings illustrate the usefulness of the methodology developed.     

Analysis of culture fluorescence by a fiber-optic sensor inNicotiana tabacum plant cell culture

The on-line sensing of viable cell weight in plant cell culture process is applied to analysis and control of process. The fiber-optic fluorescence sensor was constructed to measure the NADH-dependent fluorescence inNicotiana tabacum plant cell culture and the analysis of fluorescence signal was done to be correlated with the viable cell weight. The structured kinetic model for cell growth was proposed to estimate the theoretical viable cell weight. The dimensional analysis was proposed for the interpretation of fluorescence signal, in which the path length, the inner filter effect and the hydrodynamic conditions were considered as the key factors on fluorescence signal. The dimensional analysis and empirical correlation of fluorescence signal to viable cell weight was applied to the interpretation of the detected fluorescence signal during cultivation. The proposed interpretation of fluorescence signal using dimensional analysis was well correlated with the viable cell weight estimated by the structured kinetic model as well as by empirical correlation.     

Velocity Profile in Fixed Beds: A Study on the Representativeness of the Experimental Measurement of Downstream Flow Characteristics

Although considerable progress has been made in the development of experimental techniques for investigating velocity distribution inside a fixed bed, these techniques were limited to special cases. Consequently, the velocity distribution is normally measured at downstream of the fixed bed and then this measurement is considered to be representative for the flow inside the bed. To evaluate the representativeness of this technique, this work presents a study of the change in the flow characteristics, starting from the boundary of the fixed bed within the pipe to a downstream position where the experimental measurement is taken, by using simulations based on computational fluid dynamics methods.     

中国先进研究堆堵流事故分析

堵流事故是板状燃料研究堆发生概率相对较高的一种事故。本文进行CARR堵流事故分析时,假定额定功率运行下,1盒燃料组件的入口全部堵塞。用Relap5\Scdapsim\Mod3．2程序分析堵流事故时反应性、堆功率、压力、流量和温度等的变化,并分析发生堵流的标准燃料组件对周边燃料组件的影响。结果表明,发生堵流的燃料组件将烧毁,但不向相邻的组件扩展。CARR设计采取的安全措施可以把堵流事故后果控制在可接受范围之内。     

低压铸造流动与传热耦合计算的研究

根据低压铸造充型流动的特点 ,利用计算机数值模拟技术 ,对低压铸造充型阶段的流动怀传热过程进行了耦合计算 ,从而保证了模拟结果的准确性和可靠性。在此基础上开发出了模拟软件 ,并对实际低压铸件进行了模拟分析 ,结果与实际生产情况吻合很好     

Tree-shaped flow structures designed by minimizing path lengths

This paper outlines a direct route to the construction of effective tree-shaped flow structures. Dendritic flow structures dominate the design of natural and engineered flow systems, especially in thermal and fluid systems. The starting point is the optimization of the shape of each elemental area or volume, such that the length of the flow path housed by the element is minimized. Proceeding toward larger and more complex structures - from elements, to first constructs, second constructs, etc. - the paper develops tree-shaped flow structures between one point and a straight line, one point and a plane, a circle and its center, and a point and many points distributed uniformly over an area. In the latter, the construction method is applied to a fluid flow configuration with laminar fully developed flow. The constructions reveal several features that are supported by empirical observations of natural tree-shaped flows: asymmetry, flow rate imbalance, pairing or bifurcation, angles between branches, and Y-shaped constructs that lie in a plane. It is shown that these basic features are necessary because of “packing”, i.e., assembling optimized elements into a fixed space, and filling the space completely. For the flow between an area and one point, the best elemental shape is the regular hexagon. It is shown that the emergence of string-shaped links that connect two or more elements are necessary features, which are also required by packing. Strings cover some of the inner zones of the tree network, particularly the inner zones of large and complex trees. Dichotomous Y-shaped constructs dominate the tree structure, especially the peripheral zones of the tree canopy. The practical importance of the simplified design method is discussed.