Towards implementation of a nickel silicide process for CMOS technologies

In this paper, we review some of the advantages and disadvantages of nickel silicide as a material for the electrical contacts to the source, drain and gate of current and future CMOS devices. We first present some of the limitations imposed on the current cobalt silicide process because of the constant scaling, of the introduction of new substrate geometries (i.e. thin silicon on insulator) and of the modifications to the substrate material (i.e. SiGe). We then discuss the advantages of NiSi and for each of the CoSi₂ limitations, we point out why Ni is believed to be superior from the point of view of material properties, miscibility of phases and formation mechanisms. Discussion follows on the expected limitations of NiSi and some of the possible solutions to palliate these limitations.     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

WuM1-1羽状分支水平井充气钻井液技术

WuM1-1井由1口多分支水平井和1口采气的直井组成。该井斜井段短,井斜率在30°/100 m以上,主井眼和10个分支井段总进尺6182 m,98%以上在煤层中钻进,煤层脆、压实性较好,更易发生掉块。为满足钻井对井壁稳定性、润滑性、井眼净化以及煤层保护等的要求,采用钾铵基聚合物防塌钻井液进行充气欠平衡钻井,在钻进中保持钻井液有合适的粘度、切力,选用合适的注气压力和注气量以及当量钻井液密度;每钻完一个立柱坚持循环几分钟,上下划眼一次,并泵入CMC高粘钻井液,配合有效使用固控设备,尽量使井眼干净;复配使用粉末状固体润滑剂和液体润滑剂。该钻井液性能稳定,易于维护,悬浮携岩能力强,润滑性好,井眼畅通,保证了WuM1-1井安全、快速、优质施工。该井在煤层钻进中无阻卡现象,井壁稳定,没有出现井壁掉块或井垮现象,水平连通一次成功,10口分支井悬空侧钻一次成功,只用57 d即顺利完井,比该地区常规钻井快49倍。     

Heavy Metals Bioremediation from Polluted Water by Glass-Ceramic Materials

The objective of this research was to study the removal of cadmium and lead from an aqueous solution through a biological treatment. For this purpose a glass-ceramic material was manufactured from industrial and urban wastes. Biofilms of microorganisms found in wastewater were developed on its surface, and continuous tests were conducted in the presence and absence of the biofilm to analyze the glass-ceramic's ability to remove the heavy metals from an aqueous environment. The results suggest that this bioremediation process, developed on an industrial scale, could represent an alternative to the chemical processes currently used.     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

NSA-500-1型氩弧焊机VD9不同接法对引弧和稳弧的影响

从一起NSA－500－1型氩弧焊机故障，分析其高压脉冲旁路二极管VD9不同接法对引弧、稳弧及设备安全的影响。     

Continuous time stochastic adaptive control: non-explosion, ε-consistency and stability

For completely observed continuous time constant parameter stochastic linear systems, an indirect adaptive control law is presented which, subject principally to a weak location hypothesis concerning the true parameter, and a persistent excitation hypothesis, generates ε-consistent recursive least squares parameter estimates and ensures the system is mean square sample path stable. The adaptive control algorith mentails (i) recursively calculating the least squares estimate of the system parameter, and (ii) recursively generating the LQR feedback gain matrix lying in a set of matrix gains γ known to contain a stabilizing gain. The a.s. non-explosion of the system is a direct consequence of this construction.     

含混合金属的羟基镍铝交联蒙托石的合成

用两种方法——取代法和共聚法合成了一系列羟基镍铝交联蒙托石(GNiAl-CLM和NiAl-CLM),首次利用两种方法,交联前和交联后高温老化处理,对交联蒙托石的热稳定性进行改进。结果表明:取代法合成的羟基镍铝交联蒙托石具有均一的(001)面衍射,底面间距d(001)值均为1.8nm左右,而共聚法合成的羟基镍铝交联蒙托石出现两个(001)面衍射,d(001)值分别为1.8nm和1.55nm;高温处理后,热稳定性得到明显改进,热稳定性可高达700℃以上。     

DIRECT RESONANCE OF TURBULENT BOUNDARY LAVER OVER COMPLIANT WALLS

１．　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｍａｉｎｇｏａｌｏｆｔｈｉｓｐａｐｅｒｉｓｔｏｅｘｐｌｏｒｅｔｈｅｐｏｓｓｉｂｉｌｉｔｙｔｏｌｅａｒｎｍｏｒｅａｂｏｕｔｔｈｅｍｅｃｈａｎｉｓｍｏｆｔｕｒｂｕｌｅｎｔｂｏｕｎｄａｒｙｌａｙｅｒｆｌｏｗｉｎｔｅｒａｃｔｉｏｎｓａｎｄｉｔｓｅｆｆｅｃｔｓｏｎｃｏｍｐｌｉａｎｔｗａｌｌｐｅｒｆｏｒｍａｎｃｅ．Ｔｈｅｒｅａｒｅｃｅｒｔａｉｎｐｒｅｒｅｑｕｉｓｉｔｅｃｏｎｄｉｔｉｏｎｓｔｏｆｕｒｔｈｅｒｔｈｅｓｔｕｄｙｏｎｔｈｅｍｅｃｈａｎｉｓｍ，ｉ．ｅ．ｔｈｅｃｏ…     

I／A智能自动化系统总体构想

I/A DCS智能自动化系统是Foxboro公司80年代后期推出的DCS新产品。本文介绍了其体系结构、主要技术指标、硬件系统设计、软件系统设计、通信网络、集成控制概念及系统开放思想。从而,为建立我国自己的DCS产品提供参考。