高频微型脉冲管制冷机的实用化研究

脉冲管制冷机经过多年的发展，性能不断改善，目前已开始进入实用化阶段。高频微型脉冲管制冷机结构紧凑，应用方便，并且主要工作在需求量较大的液氮温区，因此将首先得到一定规模的应用。介绍了作者针对脉冲管制冷机在红外和超导方面的应用所作的实用化工作，讨论了尚待解决的问题。     

东方红浆砌石重力坝扬压力安全评价

东方红水库大坝是一座运行近40a的浆砌石重力坝，坝体裂缝、坝体渗漏及坝体碳化严重，扬压力有逐年增高的趋势。本文利用坝基扬压力测压管水位观测资料建立了测压管水位的统计模型，并结合现场渗漏实测流量资料建立了渗流反分析模型，详细分析了坝基的渗流性态和扬压力状态，并对其渗流性态做出安全评价。     

小功率行波管可靠性数字仿真的研究

基于对实际器件的测试数据,采用模糊数学和最可能故障法建立整个器件的可靠性模型.引入可靠性分布密度函数,将实际测试得到的离散数据拟合成随时间变化的连续函数,不仅可得到小功率行波管测试性能的评估,而且还可以对其可靠性进行预测;进一步研究,还可以给出预测的准确度概率.本文主要讨论小功率行波管可靠度评估模型的建立、数据处理与精度分析等,并对预测与准确度的概率给予简要的介绍.     

锅炉炉管爆破原因分析

对在爆裂的水冷壁管正常管段和鼓包处所取的试样分别进行化学分析、金相检验、硬度测定和高温拉伸试验。分析结果表明，在近烧嘴的炉管长期处于超温工作状态，引起该部位材质严重劣化，高温强度不断下降，当该部位的高温强度低于锅炉炉管对材质所要求的技术条件即会发生爆裂。对炉管的继续使用提出了应急的预防措施。     

FLOW OF NEWTONIAN FLUIDS THROUGH SINUSOID ALLY CONSTRICTED TUBES. NUMERICAL AND EXPERIMENTAL RESULTS

Numerical and experimental predictions of pressure drops in the flow of Newtonian fluids through sinusoidally constricted tubes (SCT) are carried out. The numerical evaluations analyzed in this work are obtained from the following methods: Geometric Iteration (GJM), Geometric Iteration with First and Second Upwinds (GIM1, GIM2), Successive Over Relaxation by Line (SORBLM), Global Galerkin Spectral Method (GGSM), Collocation (CM) and Dufort-Frankel (DFM). The GIM1, GIM2 and SORBLM are applied to SCT and explained in this work. The other methods have been previously reported in the literature with the same purpose. Experiments are accomplished for constrictions of approximately 40,60 and 80% of the average tube diameter and results compare well with numerical predictions of the steady flow. It is concluded that special attention should be given to evaluations of the friction factor ƒ for Reynolds numbers Re between the onsets of flow separation and turbulence due to flow instability. Finally, the SCT as a model for porous media (PM) is discussed.     

空调器用风冷冷凝器换热能力实验研究

实验测定了几种不同铜管、肋片组合的冷凝器在不同的风量和风机转速下的换热量，发现采用内螺纹铜管和迎风侧平片、背风侧冲缝片的冷凝器具有最优的换热性能。分析了多流路冷凝器中不同流路之间的制冷剂分配不均匀性和再热现象。     

钢管打捆包装机的设计

为了提高包装质量，取代原人工打捆，设计开发了钢管打捆包装机，该包装机采用碾拉工艺，通过综合分析拉紧与绞纽组合动作的传动，实现了钢管的打捆包装机械化，使钢管包装质量达到了ISO9000标准要求，同时降低了劳动强度。     

70m3聚合釜粘釜的原因与对策

分析了70m^3聚合釜粘釜的原因，并提出了相应的解决措施：(1)调整水与单体的入料总量，适当提高水油比；(2)根据季节的变化，合理使用不同品种与数量的引发剂；(3)提高去离子水初始温度，缩短升温时间；(4)采用防粘釜性能好的涂布剂“欧洲黄”，加强清釜后的底涂操作。     

Morphological and kinetics study of PEO/PVC blends

The kinetics of spherulite radial growth and the morphology of the compatible system PEO/PVC have been studied by optical microscopy. The usual spherulite radial growth behaviour has been found for compatible blends with PEO content higher than 70%. For lower composition, distortion of the usual spherulite morphology has been observed; the anomalies have been attributed to partial miscibility of the components.     

三辊穿孔和轧管所产生的钢管壁厚极差和波浪形内螺纹

定量描述了实际生产过程中三辊斜轧穿孔所产生的钢管壁厚极差和波浪形内螺纹，初步探讨了三辊轧管机对钢管壁厚极差和波浪形内螺纹的影响。